Initial commit; kernel source import

Documentation/devicetree/bindings/sound/ak4104.txt

@@ -0,0 +1,22 @@
+AK4104 S/PDIF transmitter
+
+This device supports SPI mode only.
+
+Required properties:
+
+  - compatible : "asahi-kasei,ak4104"
+
+  - reg : The chip select number on the SPI bus
+
+Optional properties:
+
+  - reset-gpio : a GPIO spec for the reset pin. If specified, it will be
+		 deasserted before communication to the device starts.
+
+Example:
+
+spdif: ak4104@0 {
+	compatible = "asahi-kasei,ak4104";
+	reg = <0>;
+	spi-max-frequency = <5000000>;
+};

Documentation/devicetree/bindings/sound/ak4642.txt

@@ -0,0 +1,17 @@
+AK4642 I2C transmitter
+
+This device supports I2C mode only.
+
+Required properties:
+
+  - compatible : "asahi-kasei,ak4642" or "asahi-kasei,ak4643" or "asahi-kasei,ak4648"
+  - reg : The chip select number on the I2C bus
+
+Example:
+
+&i2c {
+	ak4648: ak4648@0x12 {
+		compatible = "asahi-kasei,ak4642";
+		reg = <0x12>;
+	};
+};

Documentation/devicetree/bindings/sound/ak5386.txt

@@ -0,0 +1,19 @@
+AK5386 Single-ended 24-Bit 192kHz delta-sigma ADC
+
+This device has no control interface.
+
+Required properties:
+
+  - compatible : "asahi-kasei,ak5386"
+
+Optional properties:
+
+  - reset-gpio : a GPIO spec for the reset/power down pin.
+		 If specified, it will be deasserted at probe time.
+
+Example:
+
+spdif: ak5386@0 {
+	compatible = "asahi-kasei,ak5386";
+	reset-gpio = <&gpio0 23>;
+};

Documentation/devicetree/bindings/sound/alc5632.txt

@@ -0,0 +1,24 @@
+ALC5632 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+  - compatible : "realtek,alc5632"
+
+  - reg : the I2C address of the device.
+
+  - gpio-controller : Indicates this device is a GPIO controller.
+
+  - #gpio-cells : Should be two. The first cell is the pin number and the
+    second cell is used to specify optional parameters (currently unused).
+
+Example:
+
+alc5632: alc5632@1e {
+	compatible = "realtek,alc5632";
+	reg = <0x1a>;
+
+	gpio-controller;
+	#gpio-cells = <2>;
+};

Documentation/devicetree/bindings/sound/atmel-at91sam9g20ek-wm8731-audio.txt

@@ -0,0 +1,26 @@
+* Atmel at91sam9g20ek wm8731 audio complex
+
+Required properties:
+  - compatible: "atmel,at91sam9g20ek-wm8731-audio"
+  - atmel,model: The user-visible name of this sound complex.
+  - atmel,audio-routing: A list of the connections between audio components.
+  - atmel,ssc-controller: The phandle of the SSC controller
+  - atmel,audio-codec: The phandle of the WM8731 audio codec
+Optional properties:
+  - pinctrl-names, pinctrl-0: Please refer to pinctrl-bindings.txt
+
+Example:
+sound {
+	compatible = "atmel,at91sam9g20ek-wm8731-audio";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pck0_as_mck>;
+
+	atmel,model = "wm8731 @ AT91SAMG20EK";
+
+	atmel,audio-routing =
+		"Ext Spk", "LHPOUT",
+		"Int MIC", "MICIN";
+
+	atmel,ssc-controller = <&ssc0>;
+	atmel,audio-codec = <&wm8731>;
+};

Documentation/devicetree/bindings/sound/cs4270.txt

@@ -0,0 +1,21 @@
+CS4270 audio CODEC
+
+The driver for this device currently only supports I2C.
+
+Required properties:
+
+  - compatible : "cirrus,cs4270"
+
+  - reg : the I2C address of the device for I2C
+
+Optional properties:
+
+  - reset-gpio : a GPIO spec for the reset pin. If specified, it will be
+		 deasserted before communication to the codec starts.
+
+Example:
+
+codec: cs4270@48 {
+	compatible = "cirrus,cs4270";
+	reg = <0x48>;
+};

Documentation/devicetree/bindings/sound/cs4271.txt

@@ -0,0 +1,50 @@
+Cirrus Logic CS4271 DT bindings
+
+This driver supports both the I2C and the SPI bus.
+
+Required properties:
+
+ - compatible: "cirrus,cs4271"
+
+For required properties on SPI, please consult
+Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Required properties on I2C:
+
+ - reg: the i2c address
+
+
+Optional properties:
+
+ - reset-gpio: 	a GPIO spec to define which pin is connected to the chip's
+		!RESET pin
+ - cirrus,amuteb-eq-bmutec:	When given, the Codec's AMUTEB=BMUTEC flag
+				is enabled.
+ - cirrus,enable-soft-reset:
+	The CS4271 requires its LRCLK and MCLK to be stable before its RESET
+	line is de-asserted. That also means that clocks cannot be changed
+	without putting the chip back into hardware reset, which also requires
+	a complete re-initialization of all registers.
+
+	One (undocumented) workaround is to assert and de-assert the PDN bit
+	in the MODE2 register. This workaround can be enabled with this DT
+	property.
+
+	Note that this is not needed in case the clocks are stable
+	throughout the entire runtime of the codec.
+
+Examples:
+
+	codec_i2c: cs4271@10 {
+		compatible = "cirrus,cs4271";
+		reg = <0x10>;
+		reset-gpio = <&gpio 23 0>;
+	};
+
+	codec_spi: cs4271@0 {
+		compatible = "cirrus,cs4271";
+		reg = <0x0>;
+		reset-gpio = <&gpio 23 0>;
+		spi-max-frequency = <6000000>;
+	};
+

Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt

@@ -0,0 +1,45 @@
+Texas Instruments McASP controller
+
+Required properties:
+- compatible :
+	"ti,dm646x-mcasp-audio"	: for DM646x platforms
+	"ti,da830-mcasp-audio"	: for both DA830 & DA850 platforms
+	"ti,omap2-mcasp-audio"	: for OMAP2 platforms (TI81xx, AM33xx)
+
+- reg : Should contain McASP registers offset and length
+- interrupts : Interrupt number for McASP
+- op-mode : I2S/DIT ops mode.
+- tdm-slots : Slots for TDM operation.
+- num-serializer : Serializers used by McASP.
+- serial-dir : A list of serializer pin mode. The list number should be equal
+		to "num-serializer" parameter. Each entry is a number indication
+		serializer pin direction. (0 - INACTIVE, 1 - TX, 2 - RX)
+
+
+Optional properties:
+
+- ti,hwmods : Must be "mcasp<n>", n is controller instance starting 0
+- tx-num-evt : FIFO levels.
+- rx-num-evt : FIFO levels.
+- sram-size-playback : size of sram to be allocated during playback
+- sram-size-capture  : size of sram to be allocated during capture
+
+Example:
+
+mcasp0: mcasp0@1d00000 {
+	compatible = "ti,da830-mcasp-audio";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	reg = <0x100000 0x3000>;
+	interrupts = <82 83>;
+	op-mode = <0>;		/* MCASP_IIS_MODE */
+	tdm-slots = <2>;
+	num-serializer = <16>;
+	serial-dir = <
+			0 0 0 0	/* 0: INACTIVE, 1: TX, 2: RX */
+			0 0 0 0
+			0 0 0 1
+			2 0 0 0 >;
+	tx-num-evt = <1>;
+	rx-num-evt = <1>;
+};

Documentation/devicetree/bindings/sound/imx-audio-sgtl5000.txt

@@ -0,0 +1,49 @@
+Freescale i.MX audio complex with SGTL5000 codec
+
+Required properties:
+- compatible : "fsl,imx-audio-sgtl5000"
+- model : The user-visible name of this sound complex
+- ssi-controller : The phandle of the i.MX SSI controller
+- audio-codec : The phandle of the SGTL5000 audio codec
+- audio-routing : A list of the connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source. Valid names could be power
+  supplies, SGTL5000 pins, and the jacks on the board:
+
+  Power supplies:
+   * Mic Bias
+
+  SGTL5000 pins:
+   * MIC_IN
+   * LINE_IN
+   * HP_OUT
+   * LINE_OUT
+
+  Board connectors:
+   * Mic Jack
+   * Line In Jack
+   * Headphone Jack
+   * Line Out Jack
+   * Ext Spk
+
+- mux-int-port : The internal port of the i.MX audio muxer (AUDMUX)
+- mux-ext-port : The external port of the i.MX audio muxer
+
+Note: The AUDMUX port numbering should start at 1, which is consistent with
+hardware manual.
+
+Example:
+
+sound {
+	compatible = "fsl,imx51-babbage-sgtl5000",
+		     "fsl,imx-audio-sgtl5000";
+	model = "imx51-babbage-sgtl5000";
+	ssi-controller = <&ssi1>;
+	audio-codec = <&sgtl5000>;
+	audio-routing =
+		"MIC_IN", "Mic Jack",
+		"Mic Jack", "Mic Bias",
+		"Headphone Jack", "HP_OUT";
+	mux-int-port = <1>;
+	mux-ext-port = <3>;
+};

Documentation/devicetree/bindings/sound/imx-audmux.txt

@@ -0,0 +1,13 @@
+Freescale Digital Audio Mux (AUDMUX) device
+
+Required properties:
+- compatible : "fsl,imx21-audmux" for AUDMUX version firstly used on i.MX21,
+  or "fsl,imx31-audmux" for the version firstly used on i.MX31.
+- reg : Should contain AUDMUX registers location and length
+
+Example:
+
+audmux@021d8000 {
+	compatible = "fsl,imx6q-audmux", "fsl,imx31-audmux";
+	reg = <0x021d8000 0x4000>;
+};

Documentation/devicetree/bindings/sound/mxs-audio-sgtl5000.txt

@@ -0,0 +1,17 @@
+* Freescale MXS audio complex with SGTL5000 codec
+
+Required properties:
+- compatible: "fsl,mxs-audio-sgtl5000"
+- model: The user-visible name of this sound complex
+- saif-controllers: The phandle list of the MXS SAIF controller
+- audio-codec: The phandle of the SGTL5000 audio codec
+
+Example:
+
+sound {
+	compatible = "fsl,imx28-evk-sgtl5000",
+		     "fsl,mxs-audio-sgtl5000";
+	model = "imx28-evk-sgtl5000";
+	saif-controllers = <&saif0 &saif1>;
+	audio-codec = <&sgtl5000>;
+};

Documentation/devicetree/bindings/sound/mxs-saif.txt

@@ -0,0 +1,36 @@
+* Freescale MXS Serial Audio Interface (SAIF)
+
+Required properties:
+- compatible: Should be "fsl,<chip>-saif"
+- reg: Should contain registers location and length
+- interrupts: Should contain ERROR and DMA interrupts
+- fsl,saif-dma-channel: APBX DMA channel for the SAIF
+
+Optional properties:
+- fsl,saif-master: phandle to the master SAIF.  It's only required for
+  the slave SAIF.
+
+Note: Each SAIF controller should have an alias correctly numbered
+in "aliases" node.
+
+Example:
+
+aliases {
+	saif0 = &saif0;
+	saif1 = &saif1;
+};
+
+saif0: saif@80042000 {
+	compatible = "fsl,imx28-saif";
+	reg = <0x80042000 2000>;
+	interrupts = <59 80>;
+	fsl,saif-dma-channel = <4>;
+};
+
+saif1: saif@80046000 {
+	compatible = "fsl,imx28-saif";
+	reg = <0x80046000 2000>;
+	interrupts = <58 81>;
+	fsl,saif-dma-channel = <5>;
+	fsl,saif-master = <&saif0>;
+};

Documentation/devicetree/bindings/sound/nvidia,tegra-audio-alc5632.txt

@@ -0,0 +1,67 @@
+NVIDIA Tegra audio complex
+
+Required properties:
+- compatible : "nvidia,tegra-audio-alc5632"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  "pll_a" (The Tegra clock of that name),
+  "pll_a_out0" (The Tegra clock of that name),
+  "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source. Valid names for sources and
+  sinks are the ALC5632's pins:
+
+  ALC5632 pins:
+
+  * SPK_OUTP
+  * SPK_OUTN
+  * HP_OUT_L
+  * HP_OUT_R
+  * AUX_OUT_P
+  * AUX_OUT_N
+  * LINE_IN_L
+  * LINE_IN_R
+  * PHONE_P
+  * PHONE_N
+  * MIC1_P
+  * MIC1_N
+  * MIC2_P
+  * MIC2_N
+  * MICBIAS1
+  * DMICDAT
+
+  Board connectors:
+
+  * Headset Stereophone
+  * Int Spk
+  * Headset Mic
+  * Digital Mic
+
+- nvidia,i2s-controller : The phandle of the Tegra I2S controller
+- nvidia,audio-codec : The phandle of the ALC5632 audio codec
+
+Example:
+
+sound {
+	compatible = "nvidia,tegra-audio-alc5632-paz00",
+				 "nvidia,tegra-audio-alc5632";
+
+	nvidia,model = "Compal PAZ00";
+
+	nvidia,audio-routing =
+				"Int Spk", "SPK_OUTP",
+				"Int Spk", "SPK_OUTN",
+				"Headset Mic","MICBIAS1",
+				"MIC1_N", "Headset Mic",
+				"MIC1_P", "Headset Mic",
+				"Headset Stereophone", "HP_OUT_R",
+				"Headset Stereophone", "HP_OUT_L";
+
+	nvidia,i2s-controller = <&tegra_i2s1>;
+	nvidia,audio-codec = <&alc5632>;
+
+	clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
+};

Documentation/devicetree/bindings/sound/nvidia,tegra-audio-max98090.txt

@@ -0,0 +1,49 @@
+NVIDIA Tegra audio complex, with MAX98090 CODEC
+
+Required properties:
+- compatible : "nvidia,tegra-audio-max98090"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  "pll_a" (The Tegra clock of that name),
+  "pll_a_out0" (The Tegra clock of that name),
+  "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source. Valid names for sources and
+  sinks are the MAX98090's pins, and the jacks on the board.
+
+  Board connectors:
+
+  * Headphones
+  * Speakers
+  * Mic Jack
+
+- nvidia,i2s-controller : The phandle of the Tegra I2S controller that's
+  connected to the CODEC.
+- nvidia,audio-codec : The phandle of the MAX98090 audio codec. This binding
+  assumes that AIF1 on the CODEC is connected to Tegra.
+
+Optional properties:
+- nvidia,hp-det-gpios : The GPIO that detects headphones are plugged in
+- nvidia,mic-det-gpios : The GPIO that detects if an external mic is plugged in
+
+Example:
+
+  sound {
+    compatible = "nvidia,tegra-audio-max98090-venice2",
+           "nvidia,tegra-audio-max98090";
+    nvidia,model = "NVIDIA Tegra Venice2";
+
+    nvidia,audio-routing =
+      "Headphones", "HPR",
+      "Headphones", "HPL",
+      "Speakers", "SPKR",
+      "Speakers", "SPKL";
+
+    nvidia,i2s-controller = <&tegra_i2s1>;
+    nvidia,audio-codec = <&max98090>;
+
+    clocks = <&tegra_car 216>, <&tegra_car 217>, <&tegra_car 120>;
+    clock-names = "pll_a", "pll_a_out0", "mclk";
+  };

Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5640.txt

@@ -0,0 +1,72 @@
+NVIDIA Tegra audio complex, with RT5640 CODEC
+
+Required properties:
+- compatible : "nvidia,tegra-audio-rt5640"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  "pll_a" (The Tegra clock of that name),
+  "pll_a_out0" (The Tegra clock of that name),
+  "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source. Valid names for sources and
+  sinks are the RT5640's pins, and the jacks on the board:
+
+  RT5640 pins:
+
+  * DMIC1
+  * DMIC2
+  * MICBIAS1
+  * IN1P
+  * IN1R
+  * IN2P
+  * IN2R
+  * HPOL
+  * HPOR
+  * LOUTL
+  * LOUTR
+  * MONOP
+  * MONON
+  * SPOLP
+  * SPOLN
+  * SPORP
+  * SPORN
+
+  Board connectors:
+
+  * Headphones
+  * Speakers
+  * Mic Jack
+
+- nvidia,i2s-controller : The phandle of the Tegra I2S controller that's
+  connected to the CODEC.
+- nvidia,audio-codec : The phandle of the RT5640 audio codec. This binding
+  assumes that AIF1 on the CODEC is connected to Tegra.
+
+Optional properties:
+- nvidia,hp-det-gpios : The GPIO that detects headphones are plugged in
+
+Example:
+
+sound {
+	compatible = "nvidia,tegra-audio-rt5640-dalmore",
+			"nvidia,tegra-audio-rt5640";
+	nvidia,model = "NVIDIA Tegra Dalmore";
+
+	nvidia,audio-routing =
+		"Headphones", "HPOR",
+		"Headphones", "HPOL",
+		"Speakers", "SPORP",
+		"Speakers", "SPORN",
+		"Speakers", "SPOLP",
+		"Speakers", "SPOLN";
+
+	nvidia,i2s-controller = <&tegra_i2s1>;
+	nvidia,audio-codec = <&rt5640>;
+
+	nvidia,hp-det-gpios = <&gpio 143 0>; /* GPIO PR7 */
+
+	clocks = <&tegra_car 216>, <&tegra_car 217>, <&tegra_car 120>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
+};

Documentation/devicetree/bindings/sound/nvidia,tegra-audio-trimslice.txt

@@ -0,0 +1,21 @@
+NVIDIA Tegra audio complex for TrimSlice
+
+Required properties:
+- compatible : "nvidia,tegra-audio-trimslice"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  "pll_a" (The Tegra clock of that name),
+  "pll_a_out0" (The Tegra clock of that name),
+  "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
+- nvidia,i2s-controller : The phandle of the Tegra I2S1 controller
+- nvidia,audio-codec : The phandle of the WM8903 audio codec
+
+Example:
+
+sound {
+	compatible = "nvidia,tegra-audio-trimslice";
+	nvidia,i2s-controller = <&tegra_i2s1>;
+	nvidia,audio-codec = <&codec>;
+	clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
+};

Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8753.txt

@@ -0,0 +1,62 @@
+NVIDIA Tegra audio complex
+
+Required properties:
+- compatible : "nvidia,tegra-audio-wm8753"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  "pll_a" (The Tegra clock of that name),
+  "pll_a_out0" (The Tegra clock of that name),
+  "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source. Valid names for sources and
+  sinks are the WM8753's pins, and the jacks on the board:
+
+  WM8753 pins:
+
+  * LOUT1
+  * LOUT2
+  * ROUT1
+  * ROUT2
+  * MONO1
+  * MONO2
+  * OUT3
+  * OUT4
+  * LINE1
+  * LINE2
+  * RXP
+  * RXN
+  * ACIN
+  * ACOP
+  * MIC1N
+  * MIC1
+  * MIC2N
+  * MIC2
+  * Mic Bias
+
+  Board connectors:
+
+  * Headphone Jack
+  * Mic Jack
+
+- nvidia,i2s-controller : The phandle of the Tegra I2S1 controller
+- nvidia,audio-codec : The phandle of the WM8753 audio codec
+Example:
+
+sound {
+	compatible = "nvidia,tegra-audio-wm8753-whistler",
+		     "nvidia,tegra-audio-wm8753"
+	nvidia,model = "tegra-wm8753-harmony";
+
+	nvidia,audio-routing =
+		"Headphone Jack", "LOUT1",
+		"Headphone Jack", "ROUT1";
+
+	nvidia,i2s-controller = <&i2s1>;
+	nvidia,audio-codec = <&wm8753>;
+
+	clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
+};
+

Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt

@@ -0,0 +1,79 @@
+NVIDIA Tegra audio complex
+
+Required properties:
+- compatible : "nvidia,tegra-audio-wm8903"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  "pll_a" (The Tegra clock of that name),
+  "pll_a_out0" (The Tegra clock of that name),
+  "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source. Valid names for sources and
+  sinks are the WM8903's pins, and the jacks on the board:
+
+  WM8903 pins:
+
+  * IN1L
+  * IN1R
+  * IN2L
+  * IN2R
+  * IN3L
+  * IN3R
+  * DMICDAT
+  * HPOUTL
+  * HPOUTR
+  * LINEOUTL
+  * LINEOUTR
+  * LOP
+  * LON
+  * ROP
+  * RON
+  * MICBIAS
+
+  Board connectors:
+
+  * Headphone Jack
+  * Int Spk
+  * Mic Jack
+
+- nvidia,i2s-controller : The phandle of the Tegra I2S1 controller
+- nvidia,audio-codec : The phandle of the WM8903 audio codec
+
+Optional properties:
+- nvidia,spkr-en-gpios : The GPIO that enables the speakers
+- nvidia,hp-mute-gpios : The GPIO that mutes the headphones
+- nvidia,hp-det-gpios : The GPIO that detect headphones are plugged in
+- nvidia,int-mic-en-gpios : The GPIO that enables the internal microphone
+- nvidia,ext-mic-en-gpios : The GPIO that enables the external microphone
+
+Example:
+
+sound {
+	compatible = "nvidia,tegra-audio-wm8903-harmony",
+		     "nvidia,tegra-audio-wm8903"
+	nvidia,model = "tegra-wm8903-harmony";
+
+	nvidia,audio-routing =
+		"Headphone Jack", "HPOUTR",
+		"Headphone Jack", "HPOUTL",
+		"Int Spk", "ROP",
+		"Int Spk", "RON",
+		"Int Spk", "LOP",
+		"Int Spk", "LON",
+		"Mic Jack", "MICBIAS",
+		"IN1L", "Mic Jack";
+
+	nvidia,i2s-controller = <&i2s1>;
+	nvidia,audio-codec = <&wm8903>;
+
+	nvidia,spkr-en-gpios = <&codec 2 0>;
+	nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
+	nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */
+	nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
+
+	clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
+};
+

Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt

@@ -0,0 +1,59 @@
+NVIDIA Tegra audio complex
+
+Required properties:
+- compatible : "nvidia,tegra-audio-wm9712"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  "pll_a" (The Tegra clock of that name),
+  "pll_a_out0" (The Tegra clock of that name),
+  "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source. Valid names for sources and
+  sinks are the WM9712's pins, and the jacks on the board:
+
+  WM9712 pins:
+
+  * MONOOUT
+  * HPOUTL
+  * HPOUTR
+  * LOUT2
+  * ROUT2
+  * OUT3
+  * LINEINL
+  * LINEINR
+  * PHONE
+  * PCBEEP
+  * MIC1
+  * MIC2
+  * Mic Bias
+
+  Board connectors:
+
+  * Headphone
+  * LineIn
+  * Mic
+
+- nvidia,ac97-controller : The phandle of the Tegra AC97 controller
+
+
+Example:
+
+sound {
+	compatible = "nvidia,tegra-audio-wm9712-colibri_t20",
+		         "nvidia,tegra-audio-wm9712";
+	nvidia,model = "Toradex Colibri T20";
+
+	nvidia,audio-routing =
+		"Headphone", "HPOUTL",
+		"Headphone", "HPOUTR",
+		"LineIn", "LINEINL",
+		"LineIn", "LINEINR",
+		"Mic", "MIC1";
+
+	nvidia,ac97-controller = <&ac97>;
+
+	clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
+};

Documentation/devicetree/bindings/sound/nvidia,tegra124-hda.txt

@@ -0,0 +1,14 @@
+NVIDIA Tegra30 HDA controller
+
+Required properties:
+- compatible : "nvidia,tegra30-hda"
+- reg : Should contain the HDA registers location and length.
+- interrupts : The interrupt from the hda controller.
+
+Example:
+
+hda@70030000 {
+	compatible = "nvidia,tegra-hda";
+	reg = <0x0 0x70030000 0x10000>;
+	interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+};

Documentation/devicetree/bindings/sound/nvidia,tegra20-ac97.txt

@@ -0,0 +1,22 @@
+NVIDIA Tegra 20 AC97 controller
+
+Required properties:
+- compatible : "nvidia,tegra20-ac97"
+- reg : Should contain AC97 controller registers location and length
+- interrupts : Should contain AC97 interrupt
+- nvidia,dma-request-selector : The Tegra DMA controller's phandle and
+  request selector for the AC97 controller
+- nvidia,codec-reset-gpio : The Tegra GPIO controller's phandle and the number
+  of the GPIO used to reset the external AC97 codec
+- nvidia,codec-sync-gpio : The Tegra GPIO controller's phandle and the number
+  of the GPIO corresponding with the AC97 DAP _FS line
+Example:
+
+ac97@70002000 {
+	compatible = "nvidia,tegra20-ac97";
+	reg = <0x70002000 0x200>;
+	interrupts = <0 81 0x04>;
+	nvidia,dma-request-selector = <&apbdma 12>;
+	nvidia,codec-reset-gpio = <&gpio 170 0>;
+	nvidia,codec-sync-gpio = <&gpio 120 0>;
+};

Documentation/devicetree/bindings/sound/nvidia,tegra20-das.txt

@@ -0,0 +1,12 @@
+NVIDIA Tegra 20 DAS (Digital Audio Switch) controller
+
+Required properties:
+- compatible : "nvidia,tegra20-das"
+- reg : Should contain DAS registers location and length
+
+Example:
+
+das@70000c00 {
+	compatible = "nvidia,tegra20-das";
+	reg = <0x70000c00 0x80>;
+};

Documentation/devicetree/bindings/sound/nvidia,tegra20-i2s.txt

@@ -0,0 +1,17 @@
+NVIDIA Tegra 20 I2S controller
+
+Required properties:
+- compatible : "nvidia,tegra20-i2s"
+- reg : Should contain I2S registers location and length
+- interrupts : Should contain I2S interrupt
+- nvidia,dma-request-selector : The Tegra DMA controller's phandle and
+  request selector for this I2S controller
+
+Example:
+
+i2s@70002800 {
+	compatible = "nvidia,tegra20-i2s";
+	reg = <0x70002800 0x200>;
+	interrupts = < 45 >;
+	nvidia,dma-request-selector = < &apbdma 2 >;
+};

Documentation/devicetree/bindings/sound/nvidia,tegra30-ahub.txt

@@ -0,0 +1,48 @@
+NVIDIA Tegra30 AHUB (Audio Hub)
+
+Required properties:
+- compatible : "nvidia,tegra30-ahub", "nvidia,tegra114-ahub", etc.
+- reg : Should contain the register physical address and length for each of
+  the AHUB's register blocks.
+  - Tegra30 requires 2 entries, for the APBIF and AHUB/AUDIO register blocks.
+  - Tegra114 requires an additional entry, for the APBIF2 register block.
+- interrupts : Should contain AHUB interrupt
+- nvidia,dma-request-selector : A list of the DMA channel specifiers. Each
+  entry contains the Tegra DMA controller's phandle and request selector.
+  If a single entry is present, the request selectors for the channels are
+  assumed to be contiguous, and increment from this value.
+  If multiple values are given, one value must be given per channel.
+- clocks : Must contain an entry for each required entry in clock-names.
+- clock-names : Must include the following entries:
+  - Tegra30: Requires d_audio, apbif, i2s0, i2s1, i2s2, i2s3, i2s4, dam0,
+    dam1, dam2, spdif_in.
+  - Tegra114: Additionally requires amx, adx.
+- ranges : The bus address mapping for the configlink register bus.
+  Can be empty since the mapping is 1:1.
+- #address-cells : For the configlink bus. Should be <1>;
+- #size-cells : For the configlink bus. Should be <1>.
+
+AHUB client modules need to specify the IDs of their CIFs (Client InterFaces).
+For RX CIFs, the numbers indicate the register number within AHUB routing
+register space (APBIF 0..3 RX, I2S 0..5 RX, DAM 0..2 RX 0..1, SPDIF RX 0..1).
+For TX CIFs, the numbers indicate the bit position within the AHUB routing
+registers (APBIF 0..3 TX, I2S 0..5 TX, DAM 0..2 TX, SPDIF TX 0..1).
+
+Example:
+
+ahub@70080000 {
+	compatible = "nvidia,tegra30-ahub";
+	reg = <0x70080000 0x200 0x70080200 0x100>;
+	interrupts = < 0 103 0x04 >;
+	nvidia,dma-request-selector = <&apbdma 1>;
+	clocks = <&tegra_car 106>, <&tegra_car 107>, <&tegra_car 30>,
+		<&tegra_car 11>, <&tegra_car 18>, <&tegra_car 101>,
+		<&tegra_car 102>, <&tegra_car 108>, <&tegra_car 109>,
+		<&tegra_car 110>, <&tegra_car 162>;
+	clock-names = "d_audio", "apbif", "i2s0", "i2s1", "i2s2",
+		"i2s3", "i2s4", "dam0", "dam1", "dam2",
+		"spdif_in";
+	ranges;
+	#address-cells = <1>;
+	#size-cells = <1>;
+};

Documentation/devicetree/bindings/sound/nvidia,tegra30-i2s.txt

@@ -0,0 +1,15 @@
+NVIDIA Tegra30 I2S controller
+
+Required properties:
+- compatible : "nvidia,tegra30-i2s"
+- reg : Should contain I2S registers location and length
+- nvidia,ahub-cif-ids : The list of AHUB CIF IDs for this port, rx (playback)
+  first, tx (capture) second. See nvidia,tegra30-ahub.txt for values.
+
+Example:
+
+i2s@70002800 {
+	compatible = "nvidia,tegra30-i2s";
+	reg = <0x70080300 0x100>;
+	nvidia,ahub-cif-ids = <4 4>;
+};

Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt

@@ -0,0 +1,91 @@
+* Texas Instruments OMAP4+ and twl6040 based audio setups
+
+Required properties:
+- compatible: "ti,abe-twl6040"
+- ti,model: Name of the sound card ( for example "SDP4430")
+- ti,mclk-freq: MCLK frequency for HPPLL operation
+- ti,mcpdm: phandle for the McPDM node
+- ti,twl6040: phandle for the twl6040 core node
+- ti,audio-routing: List of connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source.
+
+Optional properties:
+- ti,dmic: phandle for the OMAP dmic node if the machine have it connected
+- ti,jack_detection: Need to be present if the board capable to detect jack
+  insertion, removal.
+
+Available audio endpoints for the audio-routing table:
+
+Board connectors:
+ * Headset Stereophone
+ * Earphone Spk
+ * Ext Spk
+ * Line Out
+ * Vibrator
+ * Headset Mic
+ * Main Handset Mic
+ * Sub Handset Mic
+ * Line In
+ * Digital Mic
+
+twl6040 pins:
+ * HSOL
+ * HSOR
+ * EP
+ * HFL
+ * HFR
+ * AUXL
+ * AUXR
+ * VIBRAL
+ * VIBRAR
+ * HSMIC
+ * MAINMIC
+ * SUBMIC
+ * AFML
+ * AFMR
+
+ * Headset Mic Bias
+ * Main Mic Bias
+ * Digital Mic1 Bias
+ * Digital Mic2 Bias
+
+Digital mic pins:
+ * DMic
+
+Example:
+
+sound {
+	compatible = "ti,abe-twl6040";
+	ti,model = "SDP4430";
+
+	ti,jack-detection;
+	ti,mclk-freq = <38400000>;
+
+	ti,mcpdm = <&mcpdm>;
+	ti,dmic = <&dmic>;
+
+	ti,twl6040 = <&twl6040>;
+
+	/* Audio routing */
+	ti,audio-routing =
+		"Headset Stereophone", "HSOL",
+		"Headset Stereophone", "HSOR",
+		"Earphone Spk", "EP",
+		"Ext Spk", "HFL",
+		"Ext Spk", "HFR",
+		"Line Out", "AUXL",
+		"Line Out", "AUXR",
+		"Vibrator", "VIBRAL",
+		"Vibrator", "VIBRAR",
+		"HSMIC", "Headset Mic",
+		"Headset Mic", "Headset Mic Bias",
+		"MAINMIC", "Main Handset Mic",
+		"Main Handset Mic", "Main Mic Bias",
+		"SUBMIC", "Sub Handset Mic",
+		"Sub Handset Mic", "Main Mic Bias",
+		"AFML", "Line In",
+		"AFMR", "Line In",
+		"DMic", "Digital Mic",
+		"Digital Mic", "Digital Mic1 Bias";
+};

Documentation/devicetree/bindings/sound/omap-dmic.txt

@@ -0,0 +1,21 @@
+* Texas Instruments OMAP4+ Digital Microphone Module
+
+Required properties:
+- compatible: "ti,omap4-dmic"
+- reg: Register location and size as an array:
+       <MPU access base address, size>,
+       <L3 interconnect address, size>;
+- interrupts: Interrupt number for DMIC
+- interrupt-parent: The parent interrupt controller
+- ti,hwmods: Name of the hwmod associated with OMAP dmic IP
+
+Example:
+
+dmic: dmic@4012e000 {
+	compatible = "ti,omap4-dmic";
+	reg = <0x4012e000 0x7f>, /* MPU private access */
+	      <0x4902e000 0x7f>; /* L3 Interconnect */
+	interrupts = <0 114 0x4>;
+	interrupt-parent = <&gic>;
+	ti,hwmods = "dmic";
+};

Documentation/devicetree/bindings/sound/omap-mcbsp.txt

@@ -0,0 +1,37 @@
+* Texas Instruments OMAP2+ McBSP module
+
+Required properties:
+- compatible: "ti,omap2420-mcbsp" for McBSP on OMAP2420
+	      "ti,omap2430-mcbsp" for McBSP on OMAP2430
+	      "ti,omap3-mcbsp" for McBSP on OMAP3
+	      "ti,omap4-mcbsp" for McBSP on OMAP4 and newer SoC
+- reg: Register location and size, for OMAP4+ as an array:
+       <MPU access base address, size>,
+       <L3 interconnect address, size>;
+- reg-names: Array of strings associated with the address space
+- interrupts: Interrupt numbers for the McBSP port, as an array in case the
+	      McBSP IP have more interrupt lines:
+	<OCP compliant irq>,
+	<TX irq>,
+	<RX irq>;
+- interrupt-names: Array of strings associated with the interrupt numbers
+- interrupt-parent: The parent interrupt controller
+- ti,buffer-size: Size of the FIFO on the port (OMAP2430 and newer SoC)
+- ti,hwmods: Name of the hwmod associated to the McBSP port
+
+Example:
+
+mcbsp2: mcbsp@49022000 {
+	compatible = "ti,omap3-mcbsp";
+	reg = <0x49022000 0xff>,
+	      <0x49028000 0xff>;
+	reg-names = "mpu", "sidetone";
+	interrupts = <0 17 0x4>, /* OCP compliant interrupt */
+		     <0 62 0x4>, /* TX interrupt */
+		     <0 63 0x4>, /* RX interrupt */
+		     <0 4 0x4>;  /* Sidetone */
+	interrupt-names = "common", "tx", "rx", "sidetone";
+	interrupt-parent = <&intc>;
+	ti,buffer-size = <1280>;
+	ti,hwmods = "mcbsp2";
+};

Documentation/devicetree/bindings/sound/omap-mcpdm.txt

@@ -0,0 +1,21 @@
+* Texas Instruments OMAP4+ McPDM
+
+Required properties:
+- compatible: "ti,omap4-mcpdm"
+- reg: Register location and size as an array:
+       <MPU access base address, size>,
+       <L3 interconnect address, size>;
+- interrupts: Interrupt number for McPDM
+- interrupt-parent: The parent interrupt controller
+- ti,hwmods: Name of the hwmod associated to the McPDM
+
+Example:
+
+mcpdm: mcpdm@40132000 {
+	compatible = "ti,omap4-mcpdm";
+	reg = <0x40132000 0x7f>, /* MPU private access */
+	      <0x49032000 0x7f>; /* L3 Interconnect */
+	interrupts = <0 112 0x4>;
+	interrupt-parent = <&gic>;
+	ti,hwmods = "mcpdm";
+};

Documentation/devicetree/bindings/sound/omap-twl4030.txt

@@ -0,0 +1,63 @@
+* Texas Instruments SoC with twl4030 based audio setups
+
+Required properties:
+- compatible: "ti,omap-twl4030"
+- ti,model: Name of the sound card (for example "omap3beagle")
+- ti,mcbsp: phandle for the McBSP node
+- ti,codec: phandle for the twl4030 audio node
+
+Optional properties:
+- ti,mcbsp-voice: phandle for the McBSP node connected to the voice port of twl
+- ti, jack-det-gpio: Jack detect GPIO
+- ti,audio-routing: List of connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source.
+  If the routing is not provided all possible connection will be available
+
+Available audio endpoints for the audio-routing table:
+
+Board connectors:
+ * Headset Stereophone
+ * Earpiece Spk
+ * Handsfree Spk
+ * Ext Spk
+ * Main Mic
+ * Sub Mic
+ * Headset Mic
+ * Carkit Mic
+ * Digital0 Mic
+ * Digital1 Mic
+ * Line In
+
+twl4030 pins:
+ * HSOL
+ * HSOR
+ * EARPIECE
+ * HFL
+ * HFR
+ * PREDRIVEL
+ * PREDRIVER
+ * CARKITL
+ * CARKITR
+ * MAINMIC
+ * SUBMIC
+ * HSMIC
+ * DIGIMIC0
+ * DIGIMIC1
+ * CARKITMIC
+ * AUXL
+ * AUXR
+
+ * Headset Mic Bias
+ * Mic Bias 1 /* Used for Main Mic or Digimic0 */
+ * Mic Bias 2 /* Used for Sub Mic or Digimic1 */
+
+Example:
+
+sound {
+	compatible = "ti,omap-twl4030";
+	ti,model = "omap3beagle";
+
+	ti,mcbsp = <&mcbsp2>;
+	ti,codec = <&twl_audio>;
+};

Documentation/devicetree/bindings/sound/renesas,fsi.txt

@@ -0,0 +1,26 @@
+Renesas FSI
+
+Required properties:
+- compatible			: "renesas,sh_fsi2" or "renesas,sh_fsi"
+- reg				: Should contain the register physical address and length
+- interrupts			: Should contain FSI interrupt
+
+- fsia,spdif-connection		: FSI is connected by S/PDFI
+- fsia,stream-mode-support	: FSI supports 16bit stream mode.
+- fsia,use-internal-clock	: FSI uses internal clock when master mode.
+
+- fsib,spdif-connection		: same as fsia
+- fsib,stream-mode-support	: same as fsia
+- fsib,use-internal-clock	: same as fsia
+
+Example:
+
+sh_fsi2: sh_fsi2@0xec230000 {
+	compatible = "renesas,sh_fsi2";
+	reg = <0xec230000 0x400>;
+	interrupts = <0 146 0x4>;
+
+	fsia,spdif-connection;
+	fsia,stream-mode-support;
+	fsia,use-internal-clock;
+};

Documentation/devicetree/bindings/sound/samsung,smdk-wm8994.txt

@@ -0,0 +1,14 @@
+Samsung SMDK audio complex
+
+Required properties:
+- compatible : "samsung,smdk-wm8994"
+- samsung,i2s-controller: The phandle of the Samsung I2S0 controller
+- samsung,audio-codec: The phandle of the WM8994 audio codec
+Example:
+
+sound {
+		compatible = "samsung,smdk-wm8994";
+
+		samsung,i2s-controller = <&i2s0>;
+		samsung,audio-codec = <&wm8994>;
+};

Documentation/devicetree/bindings/sound/samsung-i2s.txt

@@ -0,0 +1,63 @@
+* Samsung I2S controller
+
+Required SoC Specific Properties:
+
+- compatible : "samsung,i2s-v5"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- dmas: list of DMA controller phandle and DMA request line ordered pairs.
+- dma-names: identifier string for each DMA request line in the dmas property.
+  These strings correspond 1:1 with the ordered pairs in dmas.
+
+Optional SoC Specific Properties:
+
+- samsung,supports-6ch: If the I2S Primary sound source has 5.1 Channel
+  support, this flag is enabled.
+- samsung,supports-rstclr: This flag should be set if I2S software reset bit
+  control is required. When this flag is set I2S software reset bit will be
+  enabled or disabled based on need.
+- samsung,supports-secdai:If I2S block has a secondary FIFO and internal DMA,
+  then this flag is enabled.
+- samsung,idma-addr: Internal DMA register base address of the audio
+  sub system(used in secondary sound source).
+
+Required Board Specific Properties:
+
+- gpios: The gpio specifier for data out,data in, LRCLK, CDCLK and SCLK
+  interface lines. The format of the gpio specifier depends on the gpio
+  controller.
+  The syntax of samsung gpio specifier is
+	<[phandle of the gpio controller node]
+	 [pin number within the gpio controller]
+	 [mux function]
+	 [flags and pull up/down]
+	 [drive strength]>
+
+Example:
+
+- SoC Specific Portion:
+
+i2s@03830000 {
+	compatible = "samsung,i2s-v5";
+	reg = <0x03830000 0x100>;
+	dmas = <&pdma0 10
+		&pdma0 9
+		&pdma0 8>;
+	dma-names = "tx", "rx", "tx-sec";
+	samsung,supports-6ch;
+	samsung,supports-rstclr;
+	samsung,supports-secdai;
+	samsung,idma-addr = <0x03000000>;
+};
+
+- Board Specific Portion:
+
+i2s@03830000 {
+	gpios = <&gpz 0 2 0 0>, /* I2S_0_SCLK */
+		<&gpz 1 2 0 0>, /* I2S_0_CDCLK */
+		<&gpz 2 2 0 0>, /* I2S_0_LRCK */
+		<&gpz 3 2 0 0>, /* I2S_0_SDI */
+		<&gpz 4 2 0 0>, /* I2S_0_SDO[1] */
+		<&gpz 5 2 0 0>, /* I2S_0_SDO[2] */
+		<&gpz 6 2 0 0>; /* I2S_0_SDO[3] */
+};

Documentation/devicetree/bindings/sound/sgtl5000.txt

@@ -0,0 +1,13 @@
+* Freescale SGTL5000 Stereo Codec
+
+Required properties:
+- compatible : "fsl,sgtl5000".
+
+- reg : the I2C address of the device
+
+Example:
+
+codec: sgtl5000@0a {
+	compatible = "fsl,sgtl5000";
+	reg = <0x0a>;
+};

Documentation/devicetree/bindings/sound/ti,tas5086.txt

@@ -0,0 +1,32 @@
+Texas Instruments TAS5086 6-channel PWM Processor
+
+Required properties:
+
+ - compatible:		Should contain "ti,tas5086".
+ - reg:			The i2c address. Should contain <0x1b>.
+
+Optional properties:
+
+ - reset-gpio: 		A GPIO spec to define which pin is connected to the
+			chip's !RESET pin. If specified, the driver will
+			assert a hardware reset at probe time.
+
+ - ti,charge-period:	This property should contain the time in microseconds
+			that closely matches the external single-ended
+			split-capacitor charge period. The hardware chip
+			waits for this period of time before starting the
+			PWM signals. This helps reduce pops and clicks.
+
+			When not specified, the hardware default of 1300ms
+			is retained.
+
+Examples:
+
+	i2c_bus {
+		tas5086@1b {
+			compatible = "ti,tas5086";
+			reg = <0x1b>;
+			reset-gpio = <&gpio 23 0>;
+			ti,charge-period = <156000>;
+		};
+	};

Documentation/devicetree/bindings/sound/tlv320aic3x.txt

@@ -0,0 +1,26 @@
+Texas Instruments - tlv320aic3x Codec module
+
+The tlv320aic3x serial control bus communicates through I2C protocols
+
+Required properties:
+- compatible - "string" -  "ti,tlv320aic3x"
+- reg - <int> -  I2C slave address
+
+
+Optional properties:
+
+- gpio-reset - gpio pin number used for codec reset
+- ai3x-gpio-func - <array of 2 int> - AIC3X_GPIO1 & AIC3X_GPIO2 Functionality
+- ai3x-micbias-vg - MicBias Voltage required.
+	1 - MICBIAS output is powered to 2.0V,
+	2 - MICBIAS output is powered to 2.5V,
+	3 - MICBIAS output is connected to AVDD,
+	If this node is not mentioned or if the value is incorrect, then MicBias
+	is powered down.
+
+Example:
+
+tlv320aic3x: tlv320aic3x@1b {
+	compatible = "ti,tlv320aic3x";
+	reg = <0x1b>;
+};

Documentation/devicetree/bindings/sound/ux500-mop500.txt

@@ -0,0 +1,39 @@
+* MOP500 Audio Machine Driver
+
+This node is responsible for linking together all ux500 Audio Driver components.
+
+Required properties:
+ - compatible              : "stericsson,snd-soc-mop500"
+
+Non-standard properties:
+ - stericsson,cpu-dai      : Phandle to the CPU-side DAI
+ - stericsson,audio-codec  : Phandle to the Audio CODEC
+ - stericsson,card-name    : Over-ride default card name
+
+Example:
+
+	sound {
+		compatible = "stericsson,snd-soc-mop500";
+
+		stericsson,cpu-dai = <&msp1 &msp3>;
+		stericsson,audio-codec = <&codec>;
+	};
+
+	msp1: msp@80124000 {
+		compatible = "stericsson,ux500-msp-i2s";
+		reg = <0x80124000 0x1000>;
+		interrupts = <0 62 0x4>;
+		v-ape-supply = <&db8500_vape_reg>;
+	};
+
+	msp3: msp@80125000 {
+		compatible = "stericsson,ux500-msp-i2s";
+		reg = <0x80125000 0x1000>;
+		interrupts = <0 62 0x4>;
+		v-ape-supply = <&db8500_vape_reg>;
+	};
+
+	codec: ab8500-codec {
+		compatible = "stericsson,ab8500-codec";
+		stericsson,earpeice-cmv = <950>; /* Units in mV. */
+	};

Documentation/devicetree/bindings/sound/ux500-msp.txt

@@ -0,0 +1,43 @@
+* ux500 MSP (CPU-side Digital Audio Interface)
+
+Required properties:
+ - compatible       :"stericsson,ux500-msp-i2s"
+ - reg              : Physical base address and length of the device's registers.
+
+Optional properties:
+ - interrupts       : The interrupt output from the device.
+ - interrupt-parent : The parent interrupt controller.
+ - <name>-supply    : Phandle to the regulator <name> supply
+
+Example:
+
+	sound {
+		compatible = "stericsson,snd-soc-mop500";
+
+		stericsson,platform-pcm-dma = <&pcm>;
+		stericsson,cpu-dai = <&msp1 &msp3>;
+		stericsson,audio-codec = <&codec>;
+	};
+
+	pcm: ux500-pcm {
+		compatible = "stericsson,ux500-pcm";
+	};
+
+	msp1: msp@80124000 {
+		compatible = "stericsson,ux500-msp-i2s";
+		reg = <0x80124000 0x1000>;
+		interrupts = <0 62 0x4>;
+		v-ape-supply = <&db8500_vape_reg>;
+	};
+
+	msp3: msp@80125000 {
+		compatible = "stericsson,ux500-msp-i2s";
+		reg = <0x80125000 0x1000>;
+		interrupts = <0 62 0x4>;
+		v-ape-supply = <&db8500_vape_reg>;
+	};
+
+	codec: ab8500-codec {
+		compatible = "stericsson,ab8500-codec";
+		stericsson,earpeice-cmv = <950>; /* Units in mV. */
+	};

Documentation/devicetree/bindings/sound/wm8510.txt

@@ -0,0 +1,18 @@
+WM8510 audio CODEC
+
+This device supports both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : "wlf,wm8510"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+Example:
+
+codec: wm8510@1a {
+	compatible = "wlf,wm8510";
+	reg = <0x1a>;
+};

Documentation/devicetree/bindings/sound/wm8523.txt

@@ -0,0 +1,16 @@
+WM8523 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+  - compatible : "wlf,wm8523"
+
+  - reg : the I2C address of the device.
+
+Example:
+
+codec: wm8523@1a {
+	compatible = "wlf,wm8523";
+	reg = <0x1a>;
+};

Documentation/devicetree/bindings/sound/wm8580.txt

@@ -0,0 +1,16 @@
+WM8580 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+  - compatible : "wlf,wm8580"
+
+  - reg : the I2C address of the device.
+
+Example:
+
+codec: wm8580@1a {
+	compatible = "wlf,wm8580";
+	reg = <0x1a>;
+};

Documentation/devicetree/bindings/sound/wm8711.txt

@@ -0,0 +1,18 @@
+WM8711 audio CODEC
+
+This device supports both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : "wlf,wm8711"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+Example:
+
+codec: wm8711@1a {
+	compatible = "wlf,wm8711";
+	reg = <0x1a>;
+};

Documentation/devicetree/bindings/sound/wm8728.txt

@@ -0,0 +1,18 @@
+WM8728 audio CODEC
+
+This device supports both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : "wlf,wm8728"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+Example:
+
+codec: wm8728@1a {
+	compatible = "wlf,wm8728";
+	reg = <0x1a>;
+};

Documentation/devicetree/bindings/sound/wm8731.txt

@@ -0,0 +1,18 @@
+WM8731 audio CODEC
+
+This device supports both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : "wlf,wm8731"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+Example:
+
+codec: wm8731@1a {
+	compatible = "wlf,wm8731";
+	reg = <0x1a>;
+};

Documentation/devicetree/bindings/sound/wm8737.txt

@@ -0,0 +1,18 @@
+WM8737 audio CODEC
+
+This device supports both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : "wlf,wm8737"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+Example:
+
+codec: wm8737@1a {
+	compatible = "wlf,wm8737";
+	reg = <0x1a>;
+};

Documentation/devicetree/bindings/sound/wm8741.txt

@@ -0,0 +1,18 @@
+WM8741 audio CODEC
+
+This device supports both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : "wlf,wm8741"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+Example:
+
+codec: wm8741@1a {
+	compatible = "wlf,wm8741";
+	reg = <0x1a>;
+};

Documentation/devicetree/bindings/sound/wm8750.txt

@@ -0,0 +1,18 @@
+WM8750 and WM8987 audio CODECs
+
+These devices support both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : "wlf,wm8750" or "wlf,wm8987"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+Example:
+
+codec: wm8750@1a {
+	compatible = "wlf,wm8750";
+	reg = <0x1a>;
+};

Documentation/devicetree/bindings/sound/wm8753.txt

@@ -0,0 +1,18 @@
+WM8753 audio CODEC
+
+This device supports both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : "wlf,wm8753"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+Example:
+
+codec: wm8737@1a {
+	compatible = "wlf,wm8753";
+	reg = <0x1a>;
+};

Documentation/devicetree/bindings/sound/wm8770.txt

@@ -0,0 +1,16 @@
+WM8770 audio CODEC
+
+This device supports SPI.
+
+Required properties:
+
+  - compatible : "wlf,wm8770"
+
+  - reg : the chip select number.
+
+Example:
+
+codec: wm8770@1 {
+	compatible = "wlf,wm8770";
+	reg = <1>;
+};

Documentation/devicetree/bindings/sound/wm8776.txt

@@ -0,0 +1,18 @@
+WM8776 audio CODEC
+
+This device supports both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : "wlf,wm8776"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+Example:
+
+codec: wm8776@1a {
+	compatible = "wlf,wm8776";
+	reg = <0x1a>;
+};

Documentation/devicetree/bindings/sound/wm8804.txt

@@ -0,0 +1,18 @@
+WM8804 audio CODEC
+
+This device supports both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : "wlf,wm8804"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+Example:
+
+codec: wm8804@1a {
+	compatible = "wlf,wm8804";
+	reg = <0x1a>;
+};

Documentation/devicetree/bindings/sound/wm8903.txt

@@ -0,0 +1,50 @@
+WM8903 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+  - compatible : "wlf,wm8903"
+
+  - reg : the I2C address of the device.
+
+  - gpio-controller : Indicates this device is a GPIO controller.
+
+  - #gpio-cells : Should be two. The first cell is the pin number and the
+    second cell is used to specify optional parameters (currently unused).
+
+Optional properties:
+
+  - interrupts : The interrupt line the codec is connected to.
+
+  - micdet-cfg : Default register value for R6 (Mic Bias). If absent, the
+    default is 0.
+
+  - micdet-delay : The debounce delay for microphone detection in mS. If
+    absent, the default is 100.
+
+  - gpio-cfg : A list of GPIO configuration register values. The list must
+    be 5 entries long. If absent, no configuration of these registers is
+    performed. If any entry has the value 0xffffffff, that GPIO's
+    configuration will not be modified.
+
+Example:
+
+codec: wm8903@1a {
+	compatible = "wlf,wm8903";
+	reg = <0x1a>;
+	interrupts = < 347 >;
+
+	gpio-controller;
+	#gpio-cells = <2>;
+
+	micdet-cfg = <0>;
+	micdet-delay = <100>;
+	gpio-cfg = <
+		0x0600 /* DMIC_LR, output */
+		0x0680 /* DMIC_DAT, input */
+		0x0000 /* GPIO, output, low */
+		0x0200 /* Interrupt, output */
+		0x01a0 /* BCLK, input, active high */
+	>;
+};

Documentation/devicetree/bindings/sound/wm8962.txt

@@ -0,0 +1,16 @@
+WM8962 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+  - compatible : "wlf,wm8962"
+
+  - reg : the I2C address of the device.
+
+Example:
+
+codec: wm8962@1a {
+	compatible = "wlf,wm8962";
+	reg = <0x1a>;
+};

Documentation/devicetree/bindings/sound/wm8994.txt

@@ -0,0 +1,74 @@
+WM1811/WM8994/WM8958 audio CODEC
+
+These devices support both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : One of "wlf,wm1811", "wlf,wm8994" or "wlf,wm8958".
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+  - gpio-controller : Indicates this device is a GPIO controller.
+  - #gpio-cells : Must be 2. The first cell is the pin number and the
+    second cell is used to specify optional parameters (currently unused).
+
+  - AVDD2-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply, CPVDD-supply,
+    SPKVDD1-supply, SPKVDD2-supply : power supplies for the device, as covered
+    in Documentation/devicetree/bindings/regulator/regulator.txt
+
+Optional properties:
+
+  - interrupts : The interrupt line the IRQ signal for the device is
+    connected to.  This is optional, if it is not connected then none
+    of the interrupt related properties should be specified.
+  - interrupt-controller : These devices contain interrupt controllers
+    and may provide interrupt services to other devices if they have an
+    interrupt line connected.
+  - interrupt-parent : The parent interrupt controller.
+  - #interrupt-cells: the number of cells to describe an IRQ, this should be 2.
+    The first cell is the IRQ number.
+    The second cell is the flags, encoded as the trigger masks from
+    Documentation/devicetree/bindings/interrupts.txt
+
+  - wlf,gpio-cfg : A list of GPIO configuration register values. If absent,
+    no configuration of these registers is performed. If any value is
+    over 0xffff then the register will be left as default. If present 11
+    values must be supplied.
+
+  - wlf,micbias-cfg : Two MICBIAS register values for WM1811 or
+    WM8958.  If absent the register defaults will be used.
+
+  - wlf,ldo1ena : GPIO specifier for control of LDO1ENA input to device.
+  - wlf,ldo2ena : GPIO specifier for control of LDO2ENA input to device.
+
+  - wlf,lineout1-se : If present LINEOUT1 is in single ended mode.
+  - wlf,lineout2-se : If present LINEOUT2 is in single ended mode.
+
+  - wlf,lineout1-feedback : If present LINEOUT1 has common mode feedback
+    connected.
+  - wlf,lineout2-feedback : If present LINEOUT2 has common mode feedback
+    connected.
+
+  - wlf,ldoena-always-driven : If present LDOENA is always driven.
+
+Example:
+
+codec: wm8994@1a {
+	compatible = "wlf,wm8994";
+	reg = <0x1a>;
+
+	gpio-controller;
+	#gpio-cells = <2>;
+
+	lineout1-se;
+
+	AVDD2-supply = <&regulator>;
+	CPVDD-supply = <&regulator>;
+	DBVDD1-supply = <&regulator>;
+	DBVDD2-supply = <&regulator>;
+	DBVDD3-supply = <&regulator>;
+	SPKVDD1-supply = <&regulator>;
+	SPKVDD2-supply = <&regulator>;
+};