nathan/Chromebook-Device-Nyan-NVIDIA-Tegra-K1-T124-Upstream-Linux-3.10-LTS-Kernel
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity

Initial commit; kernel source import

Browse Source
This commit is contained in:
Nathan
2025-04-06 23:50:55 -05:00
commit 25c6d769f4
45093 changed files with 18199410 additions and 0 deletions
Download Patch File Download Diff File Expand all files Collapse all files

29
Documentation/devicetree/bindings/net/broadcom-bcm87xx.txt Normal file
View File

@@ -0,0 +1,29 @@
The Broadcom BCM87XX devices are a family of 10G Ethernet PHYs. They
have these bindings in addition to the standard PHY bindings.
Compatible: Should contain "broadcom,bcm8706" or "broadcom,bcm8727" and
"ethernet-phy-ieee802.3-c45"
Optional Properties:
- broadcom,c45-reg-init : one of more sets of 4 cells. The first cell
is the MDIO Manageable Device (MMD) address, the second a register
address within the MMD, the third cell contains a mask to be ANDed
with the existing register value, and the fourth cell is ORed with
he result to yield the new register value. If the third cell has a
value of zero, no read of the existing value is performed.
Example:
ethernet-phy@5 {
reg = <5>;
compatible = "broadcom,bcm8706", "ethernet-phy-ieee802.3-c45";
interrupt-parent = <&gpio>;
interrupts = <12 8>; /* Pin 12, active low */
/*
* Set PMD Digital Control Register for
* GPIO[1] Tx/Rx
* GPIO[0] R64 Sync Acquired
*/
broadcom,c45-reg-init = <1 0xc808 0xff8f 0x70>;
};

18
Documentation/devicetree/bindings/net/calxeda-xgmac.txt Normal file
View File

@@ -0,0 +1,18 @@
* Calxeda Highbank 10Gb XGMAC Ethernet
Required properties:
- compatible : Should be "calxeda,hb-xgmac"
- reg : Address and length of the register set for the device
- interrupts : Should contain 3 xgmac interrupts. The 1st is main interrupt.
The 2nd is pwr mgt interrupt. The 3rd is low power state interrupt.
Optional properties:
- dma-coherent : Present if dma operations are coherent
Example:
ethernet@fff50000 {
compatible = "calxeda,hb-xgmac";
reg = <0xfff50000 0x1000>;
interrupts = <0 77 4 0 78 4 0 79 4>;
};

14
Documentation/devicetree/bindings/net/can/atmel-can.txt Normal file
View File

@@ -0,0 +1,14 @@
* AT91 CAN *
Required properties:
- compatible: Should be "atmel,at91sam9263-can" or "atmel,at91sam9x5-can"
- reg: Should contain CAN controller registers location and length
- interrupts: Should contain IRQ line for the CAN controller
Example:
can0: can@f000c000 {
compatbile = "atmel,at91sam9x5-can";
reg = <0xf000c000 0x300>;
interrupts = <40 4 5>
};

49
Documentation/devicetree/bindings/net/can/c_can.txt Normal file
View File

@@ -0,0 +1,49 @@
Bosch C_CAN/D_CAN controller Device Tree Bindings
-------------------------------------------------
Required properties:
- compatible : Should be "bosch,c_can" for C_CAN controllers and
"bosch,d_can" for D_CAN controllers.
- reg : physical base address and size of the C_CAN/D_CAN
registers map
- interrupts : property with a value describing the interrupt
number
Optional properties:
- ti,hwmods : Must be "d_can<n>" or "c_can<n>", n being the
instance number
Note: "ti,hwmods" field is used to fetch the base address and irq
resources from TI, omap hwmod data base during device registration.
Future plan is to migrate hwmod data base contents into device tree
blob so that, all the required data will be used from device tree dts
file.
Example:
Step1: SoC common .dtsi file
dcan1: d_can@481d0000 {
compatible = "bosch,d_can";
reg = <0x481d0000 0x2000>;
interrupts = <55>;
interrupt-parent = <&intc>;
status = "disabled";
};
(or)
dcan1: d_can@481d0000 {
compatible = "bosch,d_can";
ti,hwmods = "d_can1";
reg = <0x481d0000 0x2000>;
interrupts = <55>;
interrupt-parent = <&intc>;
status = "disabled";
};
Step 2: board specific .dts file
&dcan1 {
status = "okay";
};

53
Documentation/devicetree/bindings/net/can/cc770.txt Normal file
View File

@@ -0,0 +1,53 @@
Memory mapped Bosch CC770 and Intel AN82527 CAN controller
Note: The CC770 is a CAN controller from Bosch, which is 100%
compatible with the old AN82527 from Intel, but with "bugs" being fixed.
Required properties:
- compatible : should be "bosch,cc770" for the CC770 and "intc,82527"
for the AN82527.
- reg : should specify the chip select, address offset and size required
to map the registers of the controller. The size is usually 0x80.
- interrupts : property with a value describing the interrupt source
(number and sensitivity) required for the controller.
Optional properties:
- bosch,external-clock-frequency : frequency of the external oscillator
clock in Hz. Note that the internal clock frequency used by the
controller is half of that value. If not specified, a default
value of 16000000 (16 MHz) is used.
- bosch,clock-out-frequency : slock frequency in Hz on the CLKOUT pin.
If not specified or if the specified value is 0, the CLKOUT pin
will be disabled.
- bosch,slew-rate : slew rate of the CLKOUT signal. If not specified,
a resonable value will be calculated.
- bosch,disconnect-rx0-input : see data sheet.
- bosch,disconnect-rx1-input : see data sheet.
- bosch,disconnect-tx1-output : see data sheet.
- bosch,polarity-dominant : see data sheet.
- bosch,divide-memory-clock : see data sheet.
- bosch,iso-low-speed-mux : see data sheet.
For further information, please have a look to the CC770 or AN82527.
Examples:
can@3,100 {
compatible = "bosch,cc770";
reg = <3 0x100 0x80>;
interrupts = <2 0>;
interrupt-parent = <&mpic>;
bosch,external-clock-frequency = <16000000>;
};

27
Documentation/devicetree/bindings/net/can/fsl-flexcan.txt Normal file
View File

@@ -0,0 +1,27 @@
Flexcan CAN controller on Freescale's ARM and PowerPC system-on-a-chip (SOC).
Required properties:
- compatible : Should be "fsl,<processor>-flexcan"
An implementation should also claim any of the following compatibles
that it is fully backwards compatible with:
- fsl,p1010-flexcan
- reg : Offset and length of the register set for this device
- interrupts : Interrupt tuple for this device
Optional properties:
- clock-frequency : The oscillator frequency driving the flexcan device
Example:
can@1c000 {
compatible = "fsl,p1010-flexcan";
reg = <0x1c000 0x1000>;
interrupts = <48 0x2>;
interrupt-parent = <&mpic>;
clock-frequency = <200000000>; // filled in by bootloader
};

28
Documentation/devicetree/bindings/net/can/grcan.txt Normal file
View File

@@ -0,0 +1,28 @@
Aeroflex Gaisler GRCAN and GRHCAN CAN controllers.
The GRCAN and CRHCAN CAN controllers are available in the GRLIB VHDL IP core
library.
Note: These properties are built from the AMBA plug&play in a Leon SPARC system
(the ordinary environment for GRCAN and GRHCAN). There are no dts files for
sparc.
Required properties:
- name : Should be "GAISLER_GRCAN", "01_03d", "GAISLER_GRHCAN" or "01_034"
- reg : Address and length of the register set for the device
- freq : Frequency of the external oscillator clock in Hz (the frequency of
the amba bus in the ordinary case)
- interrupts : Interrupt number for this device
Optional properties:
- systemid : If not present or if the value of the least significant 16 bits
of this 32-bit property is smaller than GRCAN_TXBUG_SAFE_GRLIB_VERSION
a bug workaround is activated.
For further information look in the documentation for the GLIB IP core library:
http://www.gaisler.com/products/grlib/grip.pdf

53
Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt Normal file
View File

@@ -0,0 +1,53 @@
CAN Device Tree Bindings
------------------------
(c) 2006-2009 Secret Lab Technologies Ltd
Grant Likely <grant.likely@secretlab.ca>
fsl,mpc5200-mscan nodes
-----------------------
In addition to the required compatible-, reg- and interrupt-properties, you can
also specify which clock source shall be used for the controller:
- fsl,mscan-clock-source : a string describing the clock source. Valid values
are: "ip" for ip bus clock
"ref" for reference clock (XTAL)
"ref" is default in case this property is not
present.
fsl,mpc5121-mscan nodes
-----------------------
In addition to the required compatible-, reg- and interrupt-properties, you can
also specify which clock source and divider shall be used for the controller:
- fsl,mscan-clock-source : a string describing the clock source. Valid values
are: "ip" for ip bus clock
"ref" for reference clock
"sys" for system clock
If this property is not present, an optimal CAN
clock source and frequency based on the system
clock will be selected. If this is not possible,
the reference clock will be used.
- fsl,mscan-clock-divider: for the reference and system clock, an additional
clock divider can be specified. By default, a
value of 1 is used.
Note that the MPC5121 Rev. 1 processor is not supported.
Examples:
can@1300 {
compatible = "fsl,mpc5121-mscan";
interrupts = <12 0x8>;
interrupt-parent = <&ipic>;
reg = <0x1300 0x80>;
};
can@1380 {
compatible = "fsl,mpc5121-mscan";
interrupts = <13 0x8>;
interrupt-parent = <&ipic>;
reg = <0x1380 0x80>;
fsl,mscan-clock-source = "ref";
fsl,mscan-clock-divider = <3>;
};

53
Documentation/devicetree/bindings/net/can/sja1000.txt Normal file
View File

@@ -0,0 +1,53 @@
Memory mapped SJA1000 CAN controller from NXP (formerly Philips)
Required properties:
- compatible : should be "nxp,sja1000".
- reg : should specify the chip select, address offset and size required
to map the registers of the SJA1000. The size is usually 0x80.
- interrupts: property with a value describing the interrupt source
(number and sensitivity) required for the SJA1000.
Optional properties:
- nxp,external-clock-frequency : Frequency of the external oscillator
clock in Hz. Note that the internal clock frequency used by the
SJA1000 is half of that value. If not specified, a default value
of 16000000 (16 MHz) is used.
- nxp,tx-output-mode : operation mode of the TX output control logic:
<0x0> : bi-phase output mode
<0x1> : normal output mode (default)
<0x2> : test output mode
<0x3> : clock output mode
- nxp,tx-output-config : TX output pin configuration:
<0x01> : TX0 invert
<0x02> : TX0 pull-down (default)
<0x04> : TX0 pull-up
<0x06> : TX0 push-pull
<0x08> : TX1 invert
<0x10> : TX1 pull-down
<0x20> : TX1 pull-up
<0x30> : TX1 push-pull
- nxp,clock-out-frequency : clock frequency in Hz on the CLKOUT pin.
If not specified or if the specified value is 0, the CLKOUT pin
will be disabled.
- nxp,no-comparator-bypass : Allows to disable the CAN input comperator.
For further information, please have a look to the SJA1000 data sheet.
Examples:
can@3,100 {
compatible = "nxp,sja1000";
reg = <3 0x100 0x80>;
interrupts = <2 0>;
interrupt-parent = <&mpic>;
nxp,external-clock-frequency = <16000000>;
};

27
Documentation/devicetree/bindings/net/cavium-mdio.txt Normal file
View File

@@ -0,0 +1,27 @@
* System Management Interface (SMI) / MDIO
Properties:
- compatible: "cavium,octeon-3860-mdio"
Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
- reg: The base address of the MDIO bus controller register bank.
- #address-cells: Must be <1>.
- #size-cells: Must be <0>. MDIO addresses have no size component.
Typically an MDIO bus might have several children.
Example:
mdio@1180000001800 {
compatible = "cavium,octeon-3860-mdio";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x11800 0x00001800 0x0 0x40>;
ethernet-phy@0 {
...
reg = <0>;
};
};

39
Documentation/devicetree/bindings/net/cavium-mix.txt Normal file
View File

@@ -0,0 +1,39 @@
* MIX Ethernet controller.
Properties:
- compatible: "cavium,octeon-5750-mix"
Compatibility with all cn5XXX and cn6XXX SOCs populated with MIX
devices.
- reg: The base addresses of four separate register banks. The first
bank contains the MIX registers. The second bank the corresponding
AGL registers. The third bank are the AGL registers shared by all
MIX devices present. The fourth bank is the AGL_PRT_CTL shared by
all MIX devices present.
- cell-index: A single cell specifying which portion of the shared
register banks corresponds to this MIX device.
- interrupts: Two interrupt specifiers. The first is the MIX
interrupt routing and the second the routing for the AGL interrupts.
- mac-address: Optional, the MAC address to assign to the device.
- local-mac-address: Optional, the MAC address to assign to the device
if mac-address is not specified.
- phy-handle: Optional, a phandle for the PHY device connected to this device.
Example:
ethernet@1070000100800 {
compatible = "cavium,octeon-5750-mix";
reg = <0x10700 0x00100800 0x0 0x100>, /* MIX */
<0x11800 0xE0000800 0x0 0x300>, /* AGL */
<0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED */
<0x11800 0xE0002008 0x0 0x8>; /* AGL_PRT_CTL */
cell-index = <1>;
interrupts = <1 18>, < 1 46>;
local-mac-address = [ 00 0f b7 10 63 54 ];
phy-handle = <&phy1>;
};

98
Documentation/devicetree/bindings/net/cavium-pip.txt Normal file
View File

@@ -0,0 +1,98 @@
* PIP Ethernet nexus.
The PIP Ethernet nexus can control several data packet input/output
devices. The devices have a two level grouping scheme. There may be
several interfaces, and each interface may have several ports. These
ports might be an individual Ethernet PHY.
Properties for the PIP nexus:
- compatible: "cavium,octeon-3860-pip"
Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
- reg: The base address of the PIP's register bank.
- #address-cells: Must be <1>.
- #size-cells: Must be <0>.
Properties for PIP interfaces which is a child the PIP nexus:
- compatible: "cavium,octeon-3860-pip-interface"
Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
- reg: The interface number.
- #address-cells: Must be <1>.
- #size-cells: Must be <0>.
Properties for PIP port which is a child the PIP interface:
- compatible: "cavium,octeon-3860-pip-port"
Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
- reg: The port number within the interface group.
- mac-address: Optional, the MAC address to assign to the device.
- local-mac-address: Optional, the MAC address to assign to the device
if mac-address is not specified.
- phy-handle: Optional, a phandle for the PHY device connected to this device.
Example:
pip@11800a0000000 {
compatible = "cavium,octeon-3860-pip";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x11800 0xa0000000 0x0 0x2000>;
interface@0 {
compatible = "cavium,octeon-3860-pip-interface";
#address-cells = <1>;
#size-cells = <0>;
reg = <0>; /* interface */
ethernet@0 {
compatible = "cavium,octeon-3860-pip-port";
reg = <0x0>; /* Port */
local-mac-address = [ 00 0f b7 10 63 60 ];
phy-handle = <&phy2>;
};
ethernet@1 {
compatible = "cavium,octeon-3860-pip-port";
reg = <0x1>; /* Port */
local-mac-address = [ 00 0f b7 10 63 61 ];
phy-handle = <&phy3>;
};
ethernet@2 {
compatible = "cavium,octeon-3860-pip-port";
reg = <0x2>; /* Port */
local-mac-address = [ 00 0f b7 10 63 62 ];
phy-handle = <&phy4>;
};
ethernet@3 {
compatible = "cavium,octeon-3860-pip-port";
reg = <0x3>; /* Port */
local-mac-address = [ 00 0f b7 10 63 63 ];
phy-handle = <&phy5>;
};
};
interface@1 {
compatible = "cavium,octeon-3860-pip-interface";
#address-cells = <1>;
#size-cells = <0>;
reg = <1>; /* interface */
ethernet@0 {
compatible = "cavium,octeon-3860-pip-port";
reg = <0x0>; /* Port */
local-mac-address = [ 00 0f b7 10 63 64 ];
phy-handle = <&phy6>;
};
};
};

23
Documentation/devicetree/bindings/net/cdns-emac.txt Normal file
View File

@@ -0,0 +1,23 @@
* Cadence EMAC Ethernet controller
Required properties:
- compatible: Should be "cdns,[<chip>-]{emac}"
Use "cdns,at91rm9200-emac" Atmel at91rm9200 SoC.
or the generic form: "cdns,emac".
- reg: Address and length of the register set for the device
- interrupts: Should contain macb interrupt
- phy-mode: String, operation mode of the PHY interface.
Supported values are: "mii", "rmii".
Optional properties:
- local-mac-address: 6 bytes, mac address
Examples:
macb0: ethernet@fffc4000 {
compatible = "cdns,at91rm9200-emac";
reg = <0xfffc4000 0x4000>;
interrupts = <21>;
phy-mode = "rmii";
local-mac-address = [3a 0e 03 04 05 06];
};

95
Documentation/devicetree/bindings/net/cpsw.txt Normal file
View File

@@ -0,0 +1,95 @@
TI SoC Ethernet Switch Controller Device Tree Bindings
------------------------------------------------------
Required properties:
- compatible : Should be "ti,cpsw"
- reg : physical base address and size of the cpsw
registers map
- interrupts : property with a value describing the interrupt
number
- interrupt-parent : The parent interrupt controller
- cpdma_channels : Specifies number of channels in CPDMA
- ale_entries : Specifies No of entries ALE can hold
- bd_ram_size : Specifies internal descriptor RAM size
- rx_descs : Specifies number of Rx descriptors
- mac_control : Specifies Default MAC control register content
for the specific platform
- slaves : Specifies number for slaves
- active_slave : Specifies the slave to use for time stamping,
ethtool and SIOCGMIIPHY
- cpts_clock_mult : Numerator to convert input clock ticks into nanoseconds
- cpts_clock_shift : Denominator to convert input clock ticks into nanoseconds
Optional properties:
- ti,hwmods : Must be "cpgmac0"
- no_bd_ram : Must be 0 or 1
- dual_emac : Specifies Switch to act as Dual EMAC
Slave Properties:
Required properties:
- phy_id : Specifies slave phy id
- mac-address : Specifies slave MAC address
Optional properties:
- dual_emac_res_vlan : Specifies VID to be used to segregate the ports
Note: "ti,hwmods" field is used to fetch the base address and irq
resources from TI, omap hwmod data base during device registration.
Future plan is to migrate hwmod data base contents into device tree
blob so that, all the required data will be used from device tree dts
file.
Examples:
mac: ethernet@4A100000 {
compatible = "ti,cpsw";
reg = <0x4A100000 0x1000>;
interrupts = <55 0x4>;
interrupt-parent = <&intc>;
cpdma_channels = <8>;
ale_entries = <1024>;
bd_ram_size = <0x2000>;
no_bd_ram = <0>;
rx_descs = <64>;
mac_control = <0x20>;
slaves = <2>;
active_slave = <0>;
cpts_clock_mult = <0x80000000>;
cpts_clock_shift = <29>;
cpsw_emac0: slave@0 {
phy_id = <&davinci_mdio>, <0>;
/* Filled in by U-Boot */
mac-address = [ 00 00 00 00 00 00 ];
};
cpsw_emac1: slave@1 {
phy_id = <&davinci_mdio>, <1>;
/* Filled in by U-Boot */
mac-address = [ 00 00 00 00 00 00 ];
};
};
(or)
mac: ethernet@4A100000 {
compatible = "ti,cpsw";
ti,hwmods = "cpgmac0";
cpdma_channels = <8>;
ale_entries = <1024>;
bd_ram_size = <0x2000>;
no_bd_ram = <0>;
rx_descs = <64>;
mac_control = <0x20>;
slaves = <2>;
active_slave = <0>;
cpts_clock_mult = <0x80000000>;
cpts_clock_shift = <29>;
cpsw_emac0: slave@0 {
phy_id = <&davinci_mdio>, <0>;
/* Filled in by U-Boot */
mac-address = [ 00 00 00 00 00 00 ];
};
cpsw_emac1: slave@1 {
phy_id = <&davinci_mdio>, <1>;
/* Filled in by U-Boot */
mac-address = [ 00 00 00 00 00 00 ];
};
};

33
Documentation/devicetree/bindings/net/davinci-mdio.txt Normal file
View File

@@ -0,0 +1,33 @@
TI SoC Davinci MDIO Controller Device Tree Bindings
---------------------------------------------------
Required properties:
- compatible : Should be "ti,davinci_mdio"
- reg : physical base address and size of the davinci mdio
registers map
- bus_freq : Mdio Bus frequency
Optional properties:
- ti,hwmods : Must be "davinci_mdio"
Note: "ti,hwmods" field is used to fetch the base address and irq
resources from TI, omap hwmod data base during device registration.
Future plan is to migrate hwmod data base contents into device tree
blob so that, all the required data will be used from device tree dts
file.
Examples:
mdio: davinci_mdio@4A101000 {
compatible = "ti,cpsw";
reg = <0x4A101000 0x1000>;
bus_freq = <1000000>;
};
(or)
mdio: davinci_mdio@4A101000 {
compatible = "ti,cpsw";
ti,hwmods = "davinci_mdio";
bus_freq = <1000000>;
};

41
Documentation/devicetree/bindings/net/davinci_emac.txt Normal file
View File

@@ -0,0 +1,41 @@
* Texas Instruments Davinci EMAC
This file provides information, what the device node
for the davinci_emac interface contains.
Required properties:
- compatible: "ti,davinci-dm6467-emac";
- reg: Offset and length of the register set for the device
- ti,davinci-ctrl-reg-offset: offset to control register
- ti,davinci-ctrl-mod-reg-offset: offset to control module register
- ti,davinci-ctrl-ram-offset: offset to control module ram
- ti,davinci-ctrl-ram-size: size of control module ram
- ti,davinci-rmii-en: use RMII
- ti,davinci-no-bd-ram: has the emac controller BD RAM
- phy-handle: Contains a phandle to an Ethernet PHY.
if not, davinci_emac driver defaults to 100/FULL
- interrupts: interrupt mapping for the davinci emac interrupts sources:
4 sources: <Receive Threshold Interrupt
Receive Interrupt
Transmit Interrupt
Miscellaneous Interrupt>
Optional properties:
- local-mac-address : 6 bytes, mac address
Example (enbw_cmc board):
eth0: emac@1e20000 {
compatible = "ti,davinci-dm6467-emac";
reg = <0x220000 0x4000>;
ti,davinci-ctrl-reg-offset = <0x3000>;
ti,davinci-ctrl-mod-reg-offset = <0x2000>;
ti,davinci-ctrl-ram-offset = <0>;
ti,davinci-ctrl-ram-size = <0x2000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <33
34
35
36
>;
interrupt-parent = <&intc>;
};

91
Documentation/devicetree/bindings/net/dsa/dsa.txt Normal file
View File

@@ -0,0 +1,91 @@
Marvell Distributed Switch Architecture Device Tree Bindings
------------------------------------------------------------
Required properties:
- compatible : Should be "marvell,dsa"
- #address-cells : Must be 2, first cell is the address on the MDIO bus
and second cell is the address in the switch tree.
Second cell is used only when cascading/chaining.
- #size-cells : Must be 0
- dsa,ethernet : Should be a phandle to a valid Ethernet device node
- dsa,mii-bus : Should be a phandle to a valid MDIO bus device node
Optionnal properties:
- interrupts : property with a value describing the switch
interrupt number (not supported by the driver)
A DSA node can contain multiple switch chips which are therefore child nodes of
the parent DSA node. The maximum number of allowed child nodes is 4
(DSA_MAX_SWITCHES).
Each of these switch child nodes should have the following required properties:
- reg : Describes the switch address on the MII bus
- #address-cells : Must be 1
- #size-cells : Must be 0
A switch may have multiple "port" children nodes
Each port children node must have the following mandatory properties:
- reg : Describes the port address in the switch
- label : Describes the label associated with this port, special
labels are "cpu" to indicate a CPU port and "dsa" to
indicate an uplink/downlink port.
Note that a port labelled "dsa" will imply checking for the uplink phandle
described below.
Optionnal property:
- link : Should be a phandle to another switch's DSA port.
This property is only used when switches are being
chained/cascaded together.
Example:
dsa@0 {
compatible = "marvell,dsa";
#address-cells = <2>;
#size-cells = <0>;
interrupts = <10>;
dsa,ethernet = <&ethernet0>;
dsa,mii-bus = <&mii_bus0>;
switch@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <16 0>; /* MDIO address 16, switch 0 in tree */
port@0 {
reg = <0>;
label = "lan1";
};
port@1 {
reg = <1>;
label = "lan2";
};
port@5 {
reg = <5>;
label = "cpu";
};
switch0uplink: port@6 {
reg = <6>;
label = "dsa";
link = <&switch1uplink>;
};
};
switch@1 {
#address-cells = <1>;
#size-cells = <0>;
reg = <17 1>; /* MDIO address 17, switch 1 in tree */
switch1uplink: port@0 {
reg = <0>;
label = "dsa";
link = <&switch0uplink>;
};
};
};

28
Documentation/devicetree/bindings/net/fsl-fec.txt Normal file
View File

@@ -0,0 +1,28 @@
* Freescale Fast Ethernet Controller (FEC)
Required properties:
- compatible : Should be "fsl,<soc>-fec"
- reg : Address and length of the register set for the device
- interrupts : Should contain fec interrupt
- phy-mode : String, operation mode of the PHY interface.
Supported values are: "mii", "gmii", "sgmii", "tbi", "rmii",
"rgmii", "rgmii-id", "rgmii-rxid", "rgmii-txid", "rtbi", "smii".
Optional properties:
- local-mac-address : 6 bytes, mac address
- phy-reset-gpios : Should specify the gpio for phy reset
- phy-reset-duration : Reset duration in milliseconds. Should present
only if property "phy-reset-gpios" is available. Missing the property
will have the duration be 1 millisecond. Numbers greater than 1000 are
invalid and 1 millisecond will be used instead.
Example:
ethernet@83fec000 {
compatible = "fsl,imx51-fec", "fsl,imx27-fec";
reg = <0x83fec000 0x4000>;
interrupts = <87>;
phy-mode = "mii";
phy-reset-gpios = <&gpio2 14 0>; /* GPIO2_14 */
local-mac-address = [00 04 9F 01 1B B9];
};

130
Documentation/devicetree/bindings/net/fsl-tsec-phy.txt Normal file
View File

@@ -0,0 +1,130 @@
* MDIO IO device
The MDIO is a bus to which the PHY devices are connected. For each
device that exists on this bus, a child node should be created. See
the definition of the PHY node in booting-without-of.txt for an example
of how to define a PHY.
Required properties:
- reg : Offset and length of the register set for the device
- compatible : Should define the compatible device type for the
mdio. Currently, this is most likely to be "fsl,gianfar-mdio"
Example:
mdio@24520 {
reg = <24520 20>;
compatible = "fsl,gianfar-mdio";
ethernet-phy@0 {
......
};
};
* TBI Internal MDIO bus
As of this writing, every tsec is associated with an internal TBI PHY.
This PHY is accessed through the local MDIO bus. These buses are defined
similarly to the mdio buses, except they are compatible with "fsl,gianfar-tbi".
The TBI PHYs underneath them are similar to normal PHYs, but the reg property
is considered instructive, rather than descriptive. The reg property should
be chosen so it doesn't interfere with other PHYs on the bus.
* Gianfar-compatible ethernet nodes
Properties:
- device_type : Should be "network"
- model : Model of the device. Can be "TSEC", "eTSEC", or "FEC"
- compatible : Should be "gianfar"
- reg : Offset and length of the register set for the device
- local-mac-address : List of bytes representing the ethernet address of
this controller
- interrupts : For FEC devices, the first interrupt is the device's
interrupt. For TSEC and eTSEC devices, the first interrupt is
transmit, the second is receive, and the third is error.
- phy-handle : The phandle for the PHY connected to this ethernet
controller.
- fixed-link : <a b c d e> where a is emulated phy id - choose any,
but unique to the all specified fixed-links, b is duplex - 0 half,
1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no
pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause.
- phy-connection-type : a string naming the controller/PHY interface type,
i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "sgmii",
"tbi", or "rtbi". This property is only really needed if the connection
is of type "rgmii-id", as all other connection types are detected by
hardware.
- fsl,magic-packet : If present, indicates that the hardware supports
waking up via magic packet.
- bd-stash : If present, indicates that the hardware supports stashing
buffer descriptors in the L2.
- rx-stash-len : Denotes the number of bytes of a received buffer to stash
in the L2.
- rx-stash-idx : Denotes the index of the first byte from the received
buffer to stash in the L2.
Example:
ethernet@24000 {
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
local-mac-address = [ 00 E0 0C 00 73 00 ];
interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy0>
};
* Gianfar PTP clock nodes
General Properties:
- compatible Should be "fsl,etsec-ptp"
- reg Offset and length of the register set for the device
- interrupts There should be at least two interrupts. Some devices
have as many as four PTP related interrupts.
Clock Properties:
- fsl,tclk-period Timer reference clock period in nanoseconds.
- fsl,tmr-prsc Prescaler, divides the output clock.
- fsl,tmr-add Frequency compensation value.
- fsl,tmr-fiper1 Fixed interval period pulse generator.
- fsl,tmr-fiper2 Fixed interval period pulse generator.
- fsl,max-adj Maximum frequency adjustment in parts per billion.
These properties set the operational parameters for the PTP
clock. You must choose these carefully for the clock to work right.
Here is how to figure good values:
TimerOsc = system clock MHz
tclk_period = desired clock period nanoseconds
NominalFreq = 1000 / tclk_period MHz
FreqDivRatio = TimerOsc / NominalFreq (must be greater that 1.0)
tmr_add = ceil(2^32 / FreqDivRatio)
OutputClock = NominalFreq / tmr_prsc MHz
PulseWidth = 1 / OutputClock microseconds
FiperFreq1 = desired frequency in Hz
FiperDiv1 = 1000000 * OutputClock / FiperFreq1
tmr_fiper1 = tmr_prsc * tclk_period * FiperDiv1 - tclk_period
max_adj = 1000000000 * (FreqDivRatio - 1.0) - 1
The calculation for tmr_fiper2 is the same as for tmr_fiper1. The
driver expects that tmr_fiper1 will be correctly set to produce a 1
Pulse Per Second (PPS) signal, since this will be offered to the PPS
subsystem to synchronize the Linux clock.
Example:
ptp_clock@24E00 {
compatible = "fsl,etsec-ptp";
reg = <0x24E00 0xB0>;
interrupts = <12 0x8 13 0x8>;
interrupt-parent = < &ipic >;
fsl,tclk-period = <10>;
fsl,tmr-prsc = <100>;
fsl,tmr-add = <0x999999A4>;
fsl,tmr-fiper1 = <0x3B9AC9F6>;
fsl,tmr-fiper2 = <0x00018696>;
fsl,max-adj = <659999998>;
};

97
Documentation/devicetree/bindings/net/gpmc-eth.txt Normal file
View File

@@ -0,0 +1,97 @@
Device tree bindings for Ethernet chip connected to TI GPMC
Besides being used to interface with external memory devices, the
General-Purpose Memory Controller can be used to connect Pseudo-SRAM devices
such as ethernet controllers to processors using the TI GPMC as a data bus.
Ethernet controllers connected to TI GPMC are represented as child nodes of
the GPMC controller with an "ethernet" name.
All timing relevant properties as well as generic GPMC child properties are
explained in a separate documents. Please refer to
Documentation/devicetree/bindings/bus/ti-gpmc.txt
For the properties relevant to the ethernet controller connected to the GPMC
refer to the binding documentation of the device. For example, the documentation
for the SMSC 911x is Documentation/devicetree/bindings/net/smsc911x.txt
Child nodes need to specify the GPMC bus address width using the "bank-width"
property but is possible that an ethernet controller also has a property to
specify the I/O registers address width. Even when the GPMC has a maximum 16-bit
address width, it supports devices with 32-bit word registers.
For example with an SMSC LAN911x/912x controller connected to the TI GPMC on an
OMAP2+ board, "bank-width = <2>;" and "reg-io-width = <4>;".
Required properties:
- bank-width: Address width of the device in bytes. GPMC supports 8-bit
and 16-bit devices and so must be either 1 or 2 bytes.
- compatible: Compatible string property for the ethernet child device.
- gpmc,cs-on-ns: Chip-select assertion time
- gpmc,cs-rd-off-ns: Chip-select de-assertion time for reads
- gpmc,cs-wr-off-ns: Chip-select de-assertion time for writes
- gpmc,oe-on-ns: Output-enable assertion time
- gpmc,oe-off-ns: Output-enable de-assertion time
- gpmc,we-on-ns: Write-enable assertion time
- gpmc,we-off-ns: Write-enable de-assertion time
- gpmc,access-ns: Start cycle to first data capture (read access)
- gpmc,rd-cycle-ns: Total read cycle time
- gpmc,wr-cycle-ns: Total write cycle time
- reg: Chip-select, base address (relative to chip-select)
and size of the memory mapped for the device.
Note that base address will be typically 0 as this
is the start of the chip-select.
Optional properties:
- gpmc,XXX Additional GPMC timings and settings parameters. See
Documentation/devicetree/bindings/bus/ti-gpmc.txt
Example:
gpmc: gpmc@6e000000 {
compatible = "ti,omap3430-gpmc";
ti,hwmods = "gpmc";
reg = <0x6e000000 0x1000>;
interrupts = <20>;
gpmc,num-cs = <8>;
gpmc,num-waitpins = <4>;
#address-cells = <2>;
#size-cells = <1>;
ranges = <5 0 0x2c000000 0x1000000>;
ethernet@5,0 {
compatible = "smsc,lan9221", "smsc,lan9115";
reg = <5 0 0xff>;
bank-width = <2>;
gpmc,mux-add-data;
gpmc,cs-on-ns = <0>;
gpmc,cs-rd-off-ns = <186>;
gpmc,cs-wr-off-ns = <186>;
gpmc,adv-on-ns = <12>;
gpmc,adv-rd-off-ns = <48>;
gpmc,adv-wr-off-ns = <48>;
gpmc,oe-on-ns = <54>;
gpmc,oe-off-ns = <168>;
gpmc,we-on-ns = <54>;
gpmc,we-off-ns = <168>;
gpmc,rd-cycle-ns = <186>;
gpmc,wr-cycle-ns = <186>;
gpmc,access-ns = <114>;
gpmc,page-burst-access-ns = <6>;
gpmc,bus-turnaround-ns = <12>;
gpmc,cycle2cycle-delay-ns = <18>;
gpmc,wr-data-mux-bus-ns = <90>;
gpmc,wr-access-ns = <186>;
gpmc,cycle2cycle-samecsen;
gpmc,cycle2cycle-diffcsen;
interrupt-parent = <&gpio6>;
interrupts = <16>;
vmmc-supply = <&vddvario>;
vmmc_aux-supply = <&vdd33a>;
reg-io-width = <4>;
smsc,save-mac-address;
};
};

24
Documentation/devicetree/bindings/net/lpc-eth.txt Normal file
View File

@@ -0,0 +1,24 @@
* NXP LPC32xx SoC Ethernet Controller
Required properties:
- compatible: Should be "nxp,lpc-eth"
- reg: Address and length of the register set for the device
- interrupts: Should contain ethernet controller interrupt
Optional properties:
- phy-mode: String, operation mode of the PHY interface.
Supported values are: "mii", "rmii" (default)
- use-iram: Use LPC32xx internal SRAM (IRAM) for DMA buffering
- local-mac-address : 6 bytes, mac address
Example:
mac: ethernet@31060000 {
compatible = "nxp,lpc-eth";
reg = <0x31060000 0x1000>;
interrupt-parent = <&mic>;
interrupts = <29 0>;
phy-mode = "rmii";
use-iram;
};

25
Documentation/devicetree/bindings/net/macb.txt Normal file
View File

@@ -0,0 +1,25 @@
* Cadence MACB/GEM Ethernet controller
Required properties:
- compatible: Should be "cdns,[<chip>-]{macb|gem}"
Use "cdns,at91sam9260-macb" Atmel at91sam9260 and at91sam9263 SoCs.
Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb".
Use "cdns,pc302-gem" for Picochip picoXcell pc302 and later devices based on
the Cadence GEM, or the generic form: "cdns,gem".
- reg: Address and length of the register set for the device
- interrupts: Should contain macb interrupt
- phy-mode: String, operation mode of the PHY interface.
Supported values are: "mii", "rmii", "gmii", "rgmii".
Optional properties:
- local-mac-address: 6 bytes, mac address
Examples:
macb0: ethernet@fffc4000 {
compatible = "cdns,at32ap7000-macb";
reg = <0xfffc4000 0x4000>;
interrupts = <21>;
phy-mode = "rmii";
local-mac-address = [3a 0e 03 04 05 06];
};

23
Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt Normal file
View File

@@ -0,0 +1,23 @@
* Marvell Armada 370 / Armada XP Ethernet Controller (NETA)
Required properties:
- compatible: should be "marvell,armada-370-neta".
- reg: address and length of the register set for the device.
- interrupts: interrupt for the device
- phy: A phandle to a phy node defining the PHY address (as the reg
property, a single integer).
- phy-mode: The interface between the SoC and the PHY (a string that
of_get_phy_mode() can understand)
- clocks: a pointer to the reference clock for this device.
Example:
ethernet@d0070000 {
compatible = "marvell,armada-370-neta";
reg = <0xd0070000 0x2500>;
interrupts = <8>;
clocks = <&gate_clk 4>;
status = "okay";
phy = <&phy0>;
phy-mode = "rgmii-id";
};

39
Documentation/devicetree/bindings/net/marvell-orion-mdio.txt Normal file
View File

@@ -0,0 +1,39 @@
* Marvell MDIO Ethernet Controller interface
The Ethernet controllers of the Marvel Kirkwood, Dove, Orion5x,
MV78xx0, Armada 370 and Armada XP have an identical unit that provides
an interface with the MDIO bus. This driver handles this MDIO
interface.
Required properties:
- compatible: "marvell,orion-mdio"
- reg: address and length of the SMI register
Optional properties:
- interrupts: interrupt line number for the SMI error/done interrupt
- clocks: Phandle to the clock control device and gate bit
The child nodes of the MDIO driver are the individual PHY devices
connected to this MDIO bus. They must have a "reg" property given the
PHY address on the MDIO bus.
Example at the SoC level:
mdio {
#address-cells = <1>;
#size-cells = <0>;
compatible = "marvell,orion-mdio";
reg = <0xd0072004 0x4>;
};
And at the board level:
mdio {
phy0: ethernet-phy@0 {
reg = <0>;
};
phy1: ethernet-phy@1 {
reg = <1>;
};
}

26
Documentation/devicetree/bindings/net/mdio-gpio.txt Normal file
View File

@@ -0,0 +1,26 @@
MDIO on GPIOs
Currently defined compatibles:
- virtual,gpio-mdio
MDC and MDIO lines connected to GPIO controllers are listed in the
gpios property as described in section VIII.1 in the following order:
MDC, MDIO.
Note: Each gpio-mdio bus should have an alias correctly numbered in "aliases"
node.
Example:
aliases {
mdio-gpio0 = <&mdio0>;
};
mdio0: mdio {
compatible = "virtual,mdio-gpio";
#address-cells = <1>;
#size-cells = <0>;
gpios = <&qe_pio_a 11
&qe_pio_c 6>;
};

127
Documentation/devicetree/bindings/net/mdio-mux-gpio.txt Normal file
View File

@@ -0,0 +1,127 @@
Properties for an MDIO bus multiplexer/switch controlled by GPIO pins.
This is a special case of a MDIO bus multiplexer. One or more GPIO
lines are used to control which child bus is connected.
Required properties in addition to the generic multiplexer properties:
- compatible : mdio-mux-gpio.
- gpios : GPIO specifiers for each GPIO line. One or more must be specified.
Example :
/* The parent MDIO bus. */
smi1: mdio@1180000001900 {
compatible = "cavium,octeon-3860-mdio";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x11800 0x00001900 0x0 0x40>;
};
/*
An NXP sn74cbtlv3253 dual 1-of-4 switch controlled by a
pair of GPIO lines. Child busses 2 and 3 populated with 4
PHYs each.
*/
mdio-mux {
compatible = "mdio-mux-gpio";
gpios = <&gpio1 3 0>, <&gpio1 4 0>;
mdio-parent-bus = <&smi1>;
#address-cells = <1>;
#size-cells = <0>;
mdio@2 {
reg = <2>;
#address-cells = <1>;
#size-cells = <0>;
phy11: ethernet-phy@1 {
reg = <1>;
compatible = "marvell,88e1149r";
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <10 8>; /* Pin 10, active low */
};
phy12: ethernet-phy@2 {
reg = <2>;
compatible = "marvell,88e1149r";
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <10 8>; /* Pin 10, active low */
};
phy13: ethernet-phy@3 {
reg = <3>;
compatible = "marvell,88e1149r";
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <10 8>; /* Pin 10, active low */
};
phy14: ethernet-phy@4 {
reg = <4>;
compatible = "marvell,88e1149r";
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <10 8>; /* Pin 10, active low */
};
};
mdio@3 {
reg = <3>;
#address-cells = <1>;
#size-cells = <0>;
phy21: ethernet-phy@1 {
reg = <1>;
compatible = "marvell,88e1149r";
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <12 8>; /* Pin 12, active low */
};
phy22: ethernet-phy@2 {
reg = <2>;
compatible = "marvell,88e1149r";
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <12 8>; /* Pin 12, active low */
};
phy23: ethernet-phy@3 {
reg = <3>;
compatible = "marvell,88e1149r";
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <12 8>; /* Pin 12, active low */
};
phy24: ethernet-phy@4 {
reg = <4>;
compatible = "marvell,88e1149r";
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <12 8>; /* Pin 12, active low */
};
};
};

75
Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt Normal file
View File

@@ -0,0 +1,75 @@
Properties for an MDIO bus multiplexer controlled by a memory-mapped device
This is a special case of a MDIO bus multiplexer. A memory-mapped device,
like an FPGA, is used to control which child bus is connected. The mdio-mux
node must be a child of the memory-mapped device. The driver currently only
supports devices with eight-bit registers.
Required properties in addition to the generic multiplexer properties:
- compatible : string, must contain "mdio-mux-mmioreg"
- reg : integer, contains the offset of the register that controls the bus
multiplexer. The size field in the 'reg' property is the size of
register, and must therefore be 1.
- mux-mask : integer, contains an eight-bit mask that specifies which
bits in the register control the actual bus multiplexer. The
'reg' property of each child mdio-mux node must be constrained by
this mask.
Example:
The FPGA node defines a memory-mapped FPGA with a register space of 0x30 bytes.
For the "EMI2" MDIO bus, register 9 (BRDCFG1) controls the mux on that bus.
A bitmask of 0x6 means that bits 1 and 2 (bit 0 is lsb) are the bits on
BRDCFG1 that control the actual mux.
/* The FPGA node */
fpga: board-control@3,0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,p5020ds-fpga", "fsl,fpga-ngpixis";
reg = <3 0 0x30>;
ranges = <0 3 0 0x30>;
mdio-mux-emi2 {
compatible = "mdio-mux-mmioreg", "mdio-mux";
mdio-parent-bus = <&xmdio0>;
#address-cells = <1>;
#size-cells = <0>;
reg = <9 1>; // BRDCFG1
mux-mask = <0x6>; // EMI2
emi2_slot1: mdio@0 { // Slot 1 XAUI (FM2)
reg = <0>;
#address-cells = <1>;
#size-cells = <0>;
phy_xgmii_slot1: ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c45";
reg = <4>;
};
};
emi2_slot2: mdio@2 { // Slot 2 XAUI (FM1)
reg = <2>;
#address-cells = <1>;
#size-cells = <0>;
phy_xgmii_slot2: ethernet-phy@4 {
compatible = "ethernet-phy-ieee802.3-c45";
reg = <0>;
};
};
};
};
/* The parent MDIO bus. */
xmdio0: mdio@f1000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,fman-xmdio";
reg = <0xf1000 0x1000>;
interrupts = <100 1 0 0>;
};

136
Documentation/devicetree/bindings/net/mdio-mux.txt Normal file
View File

@@ -0,0 +1,136 @@
Common MDIO bus multiplexer/switch properties.
An MDIO bus multiplexer/switch will have several child busses that are
numbered uniquely in a device dependent manner. The nodes for an MDIO
bus multiplexer/switch will have one child node for each child bus.
Required properties:
- mdio-parent-bus : phandle to the parent MDIO bus.
- #address-cells = <1>;
- #size-cells = <0>;
Optional properties:
- Other properties specific to the multiplexer/switch hardware.
Required properties for child nodes:
- #address-cells = <1>;
- #size-cells = <0>;
- reg : The sub-bus number.
Example :
/* The parent MDIO bus. */
smi1: mdio@1180000001900 {
compatible = "cavium,octeon-3860-mdio";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x11800 0x00001900 0x0 0x40>;
};
/*
An NXP sn74cbtlv3253 dual 1-of-4 switch controlled by a
pair of GPIO lines. Child busses 2 and 3 populated with 4
PHYs each.
*/
mdio-mux {
compatible = "mdio-mux-gpio";
gpios = <&gpio1 3 0>, <&gpio1 4 0>;
mdio-parent-bus = <&smi1>;
#address-cells = <1>;
#size-cells = <0>;
mdio@2 {
reg = <2>;
#address-cells = <1>;
#size-cells = <0>;
phy11: ethernet-phy@1 {
reg = <1>;
compatible = "marvell,88e1149r";
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <10 8>; /* Pin 10, active low */
};
phy12: ethernet-phy@2 {
reg = <2>;
compatible = "marvell,88e1149r";
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <10 8>; /* Pin 10, active low */
};
phy13: ethernet-phy@3 {
reg = <3>;
compatible = "marvell,88e1149r";
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <10 8>; /* Pin 10, active low */
};
phy14: ethernet-phy@4 {
reg = <4>;
compatible = "marvell,88e1149r";
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <10 8>; /* Pin 10, active low */
};
};
mdio@3 {
reg = <3>;
#address-cells = <1>;
#size-cells = <0>;
phy21: ethernet-phy@1 {
reg = <1>;
compatible = "marvell,88e1149r";
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <12 8>; /* Pin 12, active low */
};
phy22: ethernet-phy@2 {
reg = <2>;
compatible = "marvell,88e1149r";
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <12 8>; /* Pin 12, active low */
};
phy23: ethernet-phy@3 {
reg = <3>;
compatible = "marvell,88e1149r";
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <12 8>; /* Pin 12, active low */
};
phy24: ethernet-phy@4 {
reg = <4>;
compatible = "marvell,88e1149r";
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <12 8>; /* Pin 12, active low */
};
};
};

35
Documentation/devicetree/bindings/net/phy.txt Normal file
View File

@@ -0,0 +1,35 @@
PHY nodes
Required properties:
- device_type : Should be "ethernet-phy"
- interrupts : <a b> where a is the interrupt number and b is a
field that represents an encoding of the sense and level
information for the interrupt. This should be encoded based on
the information in section 2) depending on the type of interrupt
controller you have.
- interrupt-parent : the phandle for the interrupt controller that
services interrupts for this device.
- reg : The ID number for the phy, usually a small integer
- linux,phandle : phandle for this node; likely referenced by an
ethernet controller node.
Optional Properties:
- compatible: Compatible list, may contain
"ethernet-phy-ieee802.3-c22" or "ethernet-phy-ieee802.3-c45" for
PHYs that implement IEEE802.3 clause 22 or IEEE802.3 clause 45
specifications. If neither of these are specified, the default is to
assume clause 22. The compatible list may also contain other
elements.
Example:
ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c22";
linux,phandle = <2452000>;
interrupt-parent = <40000>;
interrupts = <35 1>;
reg = <0>;
device_type = "ethernet-phy";
};

10
Documentation/devicetree/bindings/net/smsc-lan91c111.txt Normal file
View File

@@ -0,0 +1,10 @@
SMSC LAN91c111 Ethernet mac
Required properties:
- compatible = "smsc,lan91c111";
- reg : physical address and size of registers
- interrupts : interrupt connection
Optional properties:
- phy-device : phandle to Ethernet phy
- local-mac-address : Ethernet mac address to use

38
Documentation/devicetree/bindings/net/smsc911x.txt Normal file
View File

@@ -0,0 +1,38 @@
* Smart Mixed-Signal Connectivity (SMSC) LAN911x/912x Controller
Required properties:
- compatible : Should be "smsc,lan<model>", "smsc,lan9115"
- reg : Address and length of the io space for SMSC LAN
- interrupts : Should contain SMSC LAN interrupt line
- interrupt-parent : Should be the phandle for the interrupt controller
that services interrupts for this device
- phy-mode : String, operation mode of the PHY interface.
Supported values are: "mii", "gmii", "sgmii", "tbi", "rmii",
"rgmii", "rgmii-id", "rgmii-rxid", "rgmii-txid", "rtbi", "smii".
Optional properties:
- reg-shift : Specify the quantity to shift the register offsets by
- reg-io-width : Specify the size (in bytes) of the IO accesses that
should be performed on the device. Valid value for SMSC LAN is
2 or 4. If it's omitted or invalid, the size would be 2.
- smsc,irq-active-high : Indicates the IRQ polarity is active-high
- smsc,irq-push-pull : Indicates the IRQ type is push-pull
- smsc,force-internal-phy : Forces SMSC LAN controller to use
internal PHY
- smsc,force-external-phy : Forces SMSC LAN controller to use
external PHY
- smsc,save-mac-address : Indicates that mac address needs to be saved
before resetting the controller
- local-mac-address : 6 bytes, mac address
Examples:
lan9220@f4000000 {
compatible = "smsc,lan9220", "smsc,lan9115";
reg = <0xf4000000 0x2000000>;
phy-mode = "mii";
interrupt-parent = <&gpio1>;
interrupts = <31>;
reg-io-width = <4>;
smsc,irq-push-pull;
};

29
Documentation/devicetree/bindings/net/stmmac.txt Normal file
View File

@@ -0,0 +1,29 @@
* STMicroelectronics 10/100/1000 Ethernet driver (GMAC)
Required properties:
- compatible: Should be "snps,dwmac-<ip_version>" "snps,dwmac"
For backwards compatibility: "st,spear600-gmac" is also supported.
- reg: Address and length of the register set for the device
- interrupt-parent: Should be the phandle for the interrupt controller
that services interrupts for this device
- interrupts: Should contain the STMMAC interrupts
- interrupt-names: Should contain the interrupt names "macirq"
"eth_wake_irq" if this interrupt is supported in the "interrupts"
property
- phy-mode: String, operation mode of the PHY interface.
Supported values are: "mii", "rmii", "gmii", "rgmii".
Optional properties:
- mac-address: 6 bytes, mac address
Examples:
gmac0: ethernet@e0800000 {
compatible = "st,spear600-gmac";
reg = <0xe0800000 0x8000>;
interrupt-parent = <&vic1>;
interrupts = <24 23>;
interrupt-names = "macirq", "eth_wake_irq";
mac-address = [000000000000]; /* Filled in by U-Boot */
phy-mode = "gmii";
};