Initial commit; kernel source import

Documentation/devicetree/bindings/misc/at25.txt

@@ -0,0 +1,35 @@
+EEPROMs (SPI) compatible with Atmel at25.
+
+Required properties:
+- compatible : "atmel,at25".
+- reg : chip select number
+- spi-max-frequency : max spi frequency to use
+- pagesize : size of the eeprom page
+- size : total eeprom size in bytes
+- address-width : number of address bits (one of 8, 16, or 24)
+
+Optional properties:
+- spi-cpha : SPI shifted clock phase, as per spi-bus bindings.
+- spi-cpol : SPI inverse clock polarity, as per spi-bus bindings.
+- read-only : this parameter-less property disables writes to the eeprom
+
+Obsolete legacy properties are can be used in place of "size", "pagesize",
+"address-width", and "read-only":
+- at25,byte-len : total eeprom size in bytes
+- at25,addr-mode : addr-mode flags, as defined in include/linux/spi/eeprom.h
+- at25,page-size : size of the eeprom page
+
+Additional compatible properties are also allowed.
+
+Example:
+	at25@0 {
+		compatible = "atmel,at25", "st,m95256";
+		reg = <0>
+		spi-max-frequency = <5000000>;
+		spi-cpha;
+		spi-cpol;
+
+		pagesize = <64>;
+		size = <32768>;
+		address-width = <16>;
+	};

Documentation/devicetree/bindings/misc/atmel-ssc.txt

@@ -0,0 +1,15 @@
+* Atmel SSC driver.
+
+Required properties:
+- compatible: "atmel,at91rm9200-ssc" or "atmel,at91sam9g45-ssc"
+	- atmel,at91rm9200-ssc: support pdc transfer
+	- atmel,at91sam9g45-ssc: support dma transfer
+- reg: Should contain SSC registers location and length
+- interrupts: Should contain SSC interrupt
+
+Example:
+ssc0: ssc@fffbc000 {
+	compatible = "atmel,at91rm9200-ssc";
+	reg = <0xfffbc000 0x4000>;
+	interrupts = <14 4 5>;
+};

Documentation/devicetree/bindings/misc/bmp085.txt

@@ -0,0 +1,20 @@
+BMP085/BMP18x digital pressure sensors
+
+Required properties:
+- compatible: bosch,bmp085
+
+Optional properties:
+- chip-id: configurable chip id for non-default chip revisions
+- temp-measurement-period: temperature measurement period (milliseconds)
+- default-oversampling: default oversampling value to be used at startup,
+  value range is 0-3 with rising sensitivity.
+
+Example:
+
+pressure@77 {
+	compatible = "bosch,bmp085";
+	reg = <0x77>;
+	chip-id = <10>;
+	temp-measurement-period = <100>;
+	default-oversampling = <2>;
+};

Documentation/devicetree/bindings/misc/ifm-csi.txt

@@ -0,0 +1,41 @@
+IFM camera sensor interface on mpc5200 LocalPlus bus
+
+Required properties:
+- compatible: "ifm,o2d-csi"
+- reg: specifies sensor chip select number and associated address range
+- interrupts: external interrupt line number and interrupt sense mode
+  of the interrupt line signaling frame valid events
+- gpios: three gpio-specifiers for "capture", "reset" and "master enable"
+  GPIOs (strictly in this order).
+- ifm,csi-clk-handle: the phandle to a node in the DT describing the sensor
+  clock generator. This node is usually a general purpose timer controller.
+- ifm,csi-addr-bus-width: address bus width (valid values are 16, 24, 25)
+- ifm,csi-data-bus-width: data bus width (valid values are 8 and 16)
+- ifm,csi-wait-cycles: sensor bus wait cycles
+
+Optional properties:
+- ifm,csi-byte-swap: if this property is present, the byte swapping on
+  the bus will be enabled.
+
+Example:
+
+	csi@3,0 {
+		compatible = "ifm,o2d-csi";
+		reg = <3 0 0x00100000>;		/* CS 3, 1 MiB range */
+		interrupts = <1 1 2>;		/* IRQ1, edge falling */
+
+		ifm,csi-clk-handle = <&timer7>;
+		gpios = <&gpio_simple 23 0	/* image_capture */
+			 &gpio_simple 26 0	/* image_reset */
+			 &gpio_simple 29 0>;	/* image_master_en */
+
+		ifm,csi-addr-bus-width = <24>;
+		ifm,csi-data-bus-width = <8>;
+		ifm,csi-wait-cycles = <0>;
+	};
+
+The base address of the used chip select is specified in the
+ranges property of the parent localbus node, for example:
+
+	ranges = <0 0 0xff000000 0x01000000
+		  3 0 0xe3000000 0x00100000>;

Documentation/devicetree/bindings/misc/lis302.txt

@@ -0,0 +1,112 @@
+LIS302 accelerometer devicetree bindings
+
+This device is matched via its bus drivers, and has a number of properties
+that apply in on the generic device (independent from the bus).
+
+
+Required properties for the SPI bindings:
+ - compatible: 		should be set to "st,lis3lv02d_spi"
+ - reg:			the chipselect index
+ - spi-max-frequency:	maximal bus speed, should be set to 1000000 unless
+			constrained by external circuitry
+ - interrupts:		the interrupt generated by the device
+
+Required properties for the I2C bindings:
+ - compatible:		should be set to "st,lis3lv02d"
+ - reg:			i2c slave address
+ - Vdd-supply:		The input supply for Vdd
+ - Vdd_IO-supply:	The input supply for Vdd_IO
+
+
+Optional properties for all bus drivers:
+
+ - st,click-single-{x,y,z}:	if present, tells the device to issue an
+				interrupt on single click events on the
+				x/y/z axis.
+ - st,click-double-{x,y,z}:	if present, tells the device to issue an
+				interrupt on double click events on the
+				x/y/z axis.
+ - st,click-thresh-{x,y,z}:	set the x/y/z axis threshold
+ - st,click-click-time-limit:	click time limit, from 0 to 127.5msec
+				with step of 0.5 msec
+ - st,click-latency:		click latency, from 0 to 255 msec with
+				step of 1 msec.
+ - st,click-window:		click window, from 0 to 255 msec with
+				step of 1 msec.
+ - st,irq{1,2}-disable:		disable IRQ 1/2
+ - st,irq{1,2}-ff-wu-1:		raise IRQ 1/2 on FF_WU_1 condition
+ - st,irq{1,2}-ff-wu-2:		raise IRQ 1/2 on FF_WU_2 condition
+ - st,irq{1,2}-data-ready:	raise IRQ 1/2 on data ready contition
+ - st,irq{1,2}-click:		raise IRQ 1/2 on click condition
+ - st,irq-open-drain:		consider IRQ lines open-drain
+ - st,irq-active-low:		make IRQ lines active low
+ - st,wu-duration-1:		duration register for Free-Fall/Wake-Up
+				interrupt 1
+ - st,wu-duration-2:		duration register for Free-Fall/Wake-Up
+				interrupt 2
+ - st,wakeup-{x,y,z}-{lo,hi}:	set wakeup condition on x/y/z axis for
+				upper/lower limit
+ - st,highpass-cutoff-hz=:	1, 2, 4 or 8 for 1Hz, 2Hz, 4Hz or 8Hz of
+				highpass cut-off frequency
+ - st,hipass{1,2}-disable:	disable highpass 1/2.
+ - st,default-rate=:		set the default rate
+ - st,axis-{x,y,z}=:		set the axis to map to the three coordinates
+ - st,{min,max}-limit-{x,y,z}	set the min/max limits for x/y/z axis
+				(used by self-test)
+
+
+Example for a SPI device node:
+
+	lis302@0 {
+		compatible = "st,lis302dl-spi";
+		reg = <0>;
+		spi-max-frequency = <1000000>;
+		interrupt-parent = <&gpio>;
+		interrupts = <104 0>;
+
+		st,click-single-x;
+		st,click-single-y;
+		st,click-single-z;
+		st,click-thresh-x = <10>;
+		st,click-thresh-y = <10>;
+		st,click-thresh-z = <10>;
+		st,irq1-click;
+		st,irq2-click;
+		st,wakeup-x-lo;
+		st,wakeup-x-hi;
+		st,wakeup-y-lo;
+		st,wakeup-y-hi;
+		st,wakeup-z-lo;
+		st,wakeup-z-hi;
+	};
+
+Example for a I2C device node:
+
+	lis331dlh: lis331dlh@18 {
+		compatible = "st,lis331dlh", "st,lis3lv02d";
+		reg = <0x18>;
+		Vdd-supply = <&lis3_reg>;
+		Vdd_IO-supply = <&lis3_reg>;
+
+		st,click-single-x;
+		st,click-single-y;
+		st,click-single-z;
+		st,click-thresh-x = <10>;
+		st,click-thresh-y = <10>;
+		st,click-thresh-z = <10>;
+		st,irq1-click;
+		st,irq2-click;
+		st,wakeup-x-lo;
+		st,wakeup-x-hi;
+		st,wakeup-y-lo;
+		st,wakeup-y-hi;
+		st,wakeup-z-lo;
+		st,wakeup-z-hi;
+		st,min-limit-x = <120>;
+		st,min-limit-y = <120>;
+		st,min-limit-z = <140>;
+		st,max-limit-x = <550>;
+		st,max-limit-y = <550>;
+		st,max-limit-z = <750>;
+	};
+

Documentation/devicetree/bindings/misc/smc.txt

@@ -0,0 +1,14 @@
+Broadcom Secure Monitor Bounce buffer
+-----------------------------------------------------
+This binding defines the location of the bounce buffer
+used for non-secure to secure communications.
+
+Required properties:
+- compatible : "bcm,kona-smc"
+- reg : Location and size of bounce buffer
+
+Example:
+	smc@0x3404c000 {
+		compatible = "bcm,bcm11351-smc", "bcm,kona-smc";
+		reg = <0x3404c000 0x400>; //1 KiB in SRAM
+	};

Documentation/devicetree/bindings/misc/sram.txt

@@ -0,0 +1,16 @@
+Generic on-chip SRAM
+
+Simple IO memory regions to be managed by the genalloc API.
+
+Required properties:
+
+- compatible : mmio-sram
+
+- reg : SRAM iomem address range
+
+Example:
+
+sram: sram@5c000000 {
+	compatible = "mmio-sram";
+	reg = <0x5c000000 0x40000>; /* 256 KiB SRAM at address 0x5c000000 */
+};