Initial commit; kernel source import

Documentation/devicetree/bindings/leds/common.txt

@@ -0,0 +1,23 @@
+Common leds properties.
+
+Optional properties for child nodes:
+- label : The label for this LED.  If omitted, the label is
+  taken from the node name (excluding the unit address).
+
+- linux,default-trigger :  This parameter, if present, is a
+    string defining the trigger assigned to the LED.  Current triggers are:
+     "backlight" - LED will act as a back-light, controlled by the framebuffer
+		   system
+     "default-on" - LED will turn on (but for leds-gpio see "default-state"
+		    property in Documentation/devicetree/bindings/gpio/led.txt)
+     "heartbeat" - LED "double" flashes at a load average based rate
+     "ide-disk" - LED indicates disk activity
+     "timer" - LED flashes at a fixed, configurable rate
+
+Examples:
+
+system-status {
+	label = "Status";
+	linux,default-trigger = "heartbeat";
+	...
+};

Documentation/devicetree/bindings/leds/leds-gpio.txt

@@ -0,0 +1,52 @@
+LEDs connected to GPIO lines
+
+Required properties:
+- compatible : should be "gpio-leds".
+
+Each LED is represented as a sub-node of the gpio-leds device.  Each
+node's name represents the name of the corresponding LED.
+
+LED sub-node properties:
+- gpios :  Should specify the LED's GPIO, see "gpios property" in
+  Documentation/devicetree/bindings/gpio/gpio.txt.  Active low LEDs should be
+  indicated using flags in the GPIO specifier.
+- label :  (optional)
+  see Documentation/devicetree/bindings/leds/common.txt
+- linux,default-trigger :  (optional)
+  see Documentation/devicetree/bindings/leds/common.txt
+- default-state:  (optional) The initial state of the LED.  Valid
+  values are "on", "off", and "keep".  If the LED is already on or off
+  and the default-state property is set the to same value, then no
+  glitch should be produced where the LED momentarily turns off (or
+  on).  The "keep" setting will keep the LED at whatever its current
+  state is, without producing a glitch.  The default is off if this
+  property is not present.
+
+Examples:
+
+leds {
+	compatible = "gpio-leds";
+	hdd {
+		label = "IDE Activity";
+		gpios = <&mcu_pio 0 1>; /* Active low */
+		linux,default-trigger = "ide-disk";
+	};
+
+	fault {
+		gpios = <&mcu_pio 1 0>;
+		/* Keep LED on if BIOS detected hardware fault */
+		default-state = "keep";
+	};
+};
+
+run-control {
+	compatible = "gpio-leds";
+	red {
+		gpios = <&mpc8572 6 0>;
+		default-state = "off";
+	};
+	green {
+		gpios = <&mpc8572 7 0>;
+		default-state = "on";
+	};
+};

Documentation/devicetree/bindings/leds/leds-ns2.txt

@@ -0,0 +1,26 @@
+Binding for dual-GPIO LED found on Network Space v2 (and parents).
+
+Required properties:
+- compatible: "lacie,ns2-leds".
+
+Each LED is represented as a sub-node of the ns2-leds device.
+
+Required sub-node properties:
+- cmd-gpio: Command LED GPIO. See OF device-tree GPIO specification.
+- slow-gpio: Slow LED GPIO. See OF device-tree GPIO specification.
+
+Optional sub-node properties:
+- label: Name for this LED. If omitted, the label is taken from the node name.
+- linux,default-trigger: Trigger assigned to the LED.
+
+Example:
+
+ns2-leds {
+	compatible = "lacie,ns2-leds";
+
+	blue-sata {
+		label = "ns2:blue:sata";
+		slow-gpio = <&gpio0 29 0>;
+		cmd-gpio = <&gpio0 30 0>;
+	};
+};

Documentation/devicetree/bindings/leds/leds-pwm.txt

@@ -0,0 +1,48 @@
+LED connected to PWM
+
+Required properties:
+- compatible : should be "pwm-leds".
+
+Each LED is represented as a sub-node of the pwm-leds device.  Each
+node's name represents the name of the corresponding LED.
+
+LED sub-node properties:
+- pwms : PWM property to point to the PWM device (phandle)/port (id) and to
+  specify the period time to be used: <&phandle id period_ns>;
+- pwm-names : (optional) Name to be used by the PWM subsystem for the PWM device
+  For the pwms and pwm-names property please refer to:
+  Documentation/devicetree/bindings/pwm/pwm.txt
+- max-brightness : Maximum brightness possible for the LED
+- label :  (optional)
+  see Documentation/devicetree/bindings/leds/common.txt
+- linux,default-trigger :  (optional)
+  see Documentation/devicetree/bindings/leds/common.txt
+
+Example:
+
+twl_pwm: pwm {
+	/* provides two PWMs (id 0, 1 for PWM1 and PWM2) */
+	compatible = "ti,twl6030-pwm";
+	#pwm-cells = <2>;
+};
+
+twl_pwmled: pwmled {
+	/* provides one PWM (id 0 for Charing indicator LED) */
+	compatible = "ti,twl6030-pwmled";
+	#pwm-cells = <2>;
+};
+
+pwmleds {
+	compatible = "pwm-leds";
+	kpad {
+		label = "omap4::keypad";
+		pwms = <&twl_pwm 0 7812500>;
+		max-brightness = <127>;
+	};
+
+	charging {
+		label = "omap4:green:chrg";
+		pwms = <&twl_pwmled 0 7812500>;
+		max-brightness = <255>;
+	};
+};

Documentation/devicetree/bindings/leds/tca6507.txt

@@ -0,0 +1,33 @@
+LEDs connected to tca6507
+
+Required properties:
+- compatible : should be : "ti,tca6507".
+
+Each led is represented as a sub-node of the ti,tca6507 device.
+
+LED sub-node properties:
+- label : (optional) see Documentation/devicetree/bindings/leds/common.txt
+- reg : number of LED line (could be from 0 to 6)
+- linux,default-trigger : (optional)
+   see Documentation/devicetree/bindings/leds/common.txt
+
+Examples:
+
+tca6507@45 {
+	compatible = "ti,tca6507";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	reg = <0x45>;
+
+	led0: red-aux@0 {
+		label = "red:aux";
+		reg = <0x0>;
+	};
+
+	led1: green-aux@1 {
+		label = "green:aux";
+		reg = <0x5>;
+		linux,default-trigger = "default-on";
+	};
+};
+